Steps To Change The Parking Brake On A Chevrolet Silverado

Hello! good afternoon, this day we will made an article about Steps To Change The Parking Brake On A Chevrolet Silverado

The parking brake is there to prevent the vehicle from pulling away, moving, or the transmission from being excessively loaded. Here you will learn how Change the parking brake on a Chevrolet Silverado.

The parking or handbrake may require adjustment from time to time. This brake performs many functions necessary for the safety and well-being of critical components such as the transmission and axles.

Importance of Parking Brake on a Chevy Silverado

Change the Parking Brake on a Chevy Silverado
2007 Chevrolet Silverado

Contrary to popular belief, the parking brake is not an emergency brake and surely it is not to drift. It’s there to make sure your truck doesn’t roll while it’s parked on a hill, and also to make sure your transmission gears don’t get too loaded by the weight of the truck while it’s parked.

You can think of this brake as a cushion that supports the weight of the truck. The more you use the parking brake, the more the system weakens, and therefore needs adjustment.

How to Change the Parking Brake on a Chevrolet Silverado (1999-2006)

The Silverado 1500’s parking brake uses a one-piece shoe that contacts the inside of the rear rotors. It is adjustable, but eventually all the friction material in the shoe will wear out. Read on and learn how to change the parking brake on a Chevrolet Silverado.

When you press the parking brake pedal inside your Silverado, a cable connected to the rear parking brake shoes moves the shoes against the brake rotor. The shoe contains friction material similar to a brake pad that maintains pressure against the rotor to prevent it from turning.

Parking brake shoes are moved by a wheel cylinder that uses rods to apply pressure. Over time, the barrel and metal clip (which holds the shoes against the support plate) wear out and can cause the shoes to bind and not apply pressure against the rotors.

1- Raise/remove rear wheels and support with jack stands

Removing The Parking Brake From A Silverado
pick up the truck

If you don’t have an air or electric impact wrench, you’ll need to loosen the studs before raising the rear wheels. Uses a 21mm deep socket (or socket).

Place the jack stands under the frame rails, in front of the leaf springs.

2- Remove the rear brake calipers

There are two bolts that hold the brake calipers to the rotors. They are at the rear of the caliper and are located directly above/below each other.

DO NOT let the brake caliper hang from the rubber hose as this can damage the hose. Instead, use a piece of wire or a clamp holder and position the clamp outside of your workspace.

3- Remove the rear rotors

The next step in changing the parking brake on a Chevrolet Silverado is to remove the rear rotors. Grab both sides of the rear rotor and pull it away from the wheel hub. You may need to tap the rotor in the areas indicated on the next image.

Removing The Parking Brake From A Chevrolet Silverado
Hit the rotor in the following areas

Once the rotor is off, check the condition of the inner rotor parking brake pad surface. If there is a deep scratch or gouge, it will be necessary to change the rotor.

4- Remove the handbrake shoe

The parking or parking brake shoe is a one-piece design that almost makes a circle around the center. It connects to the center in two places. The first is in the parking brake wheel cylinder. The second is on the metal clip attached to the bucket. They are on opposite sides of the parking brake shoe.

  • Using a flathead screwdriver, push the parking brake shoe away from the metal clip. This creates a gap between the metal clip and the inner side of the brake shoe. Then grab the shoe by one end connected to the wheel cylinder and rotate it out and away from the hub.
  • You will need to twist and angle the parking brake shoe to get it to move away from the hub.

5- Reinstall the parking brake shoes, rotors, calipers and wheels

Replace The Parking Brake On A Chevy Silverado
Place the bolts

To finish changing the parking brake of a Chevrolet Silverado, what this is is to reinstall everything.

  • Slide the parking brake shoe around and over the hub.
  • Find the metal clip again and place the inside of the shoe against the inside of the metal clip. This locks the shoe against the support plate preventing it from moving forward when the emergency brake is applied.
  • Then place the ends of the shoe into the slots on the sides of the wheel cylinder.
  • Now that the new shoe is installed, slide the rotor back on.
  • The caliper will slide back over the rotor. Move the caliper into the correct position to reinstall the two bolts that secure it to the hub.
  • Now reinstall the wheels and tighten the lug nuts.

After this your Silverado pickup’s parking brake should feel like new!

Necessary materials

  • Metric socket set or socket wrench (13mm to 21mm)
  • 1/2″ air or electric impact wrench
  • 1/2″ breaker bar (if impact wrench is not available)
  • flat head screwdriver
  • Wire or clamp

Tips

When jacking up the vehicle to remove the rear wheels it is best to use a block of wood between the jack stand and the frame rail so you can eliminate damage to the frame rail itself.

The parking brake is there to prevent the vehicle from pulling away, moving, or the transmission from being excessively loaded. Here you will learn how Change the parking brake on a Chevrolet Silverado.

The parking or handbrake may require adjustment from time to time. This brake performs many functions necessary for the safety and well-being of critical components such as the transmission and axles.

Importance of Parking Brake on a Chevy Silverado

Change the Parking Brake on a Chevy Silverado
2007 Chevrolet Silverado

Contrary to popular belief, the parking brake is not an emergency brake and surely it is not to drift. It’s there to make sure your truck doesn’t roll while it’s parked on a hill, and also to make sure your transmission gears don’t get too loaded by the weight of the truck while it’s parked.

You can think of this brake as a cushion that supports the weight of the truck. The more you use the parking brake, the more the system weakens, and therefore needs adjustment.

How to Change the Parking Brake on a Chevrolet Silverado (1999-2006)

The Silverado 1500’s parking brake uses a one-piece shoe that contacts the inside of the rear rotors. It is adjustable, but eventually all the friction material in the shoe will wear out. Read on and learn how to change the parking brake on a Chevrolet Silverado.

When you press the parking brake pedal inside your Silverado, a cable connected to the rear parking brake shoes moves the shoes against the brake rotor. The shoe contains friction material similar to a brake pad that maintains pressure against the rotor to prevent it from turning.

Parking brake shoes are moved by a wheel cylinder that uses rods to apply pressure. Over time, the barrel and metal clip (which holds the shoes against the support plate) wear out and can cause the shoes to bind and not apply pressure against the rotors.

1- Raise/remove rear wheels and support with jack stands

Removing The Parking Brake From A Silverado
pick up the truck

If you don’t have an air or electric impact wrench, you’ll need to loosen the studs before raising the rear wheels. Uses a 21mm deep socket (or socket).

Place the jack stands under the frame rails, in front of the leaf springs.

2- Remove the rear brake calipers

There are two bolts that hold the brake calipers to the rotors. They are at the rear of the caliper and are located directly above/below each other.

DO NOT let the brake caliper hang from the rubber hose as this can damage the hose. Instead, use a piece of wire or a clamp holder and position the clamp outside of your workspace.

3- Remove the rear rotors

The next step in changing the parking brake on a Chevrolet Silverado is to remove the rear rotors. Grab both sides of the rear rotor and pull it away from the wheel hub. You may need to tap the rotor in the areas indicated on the next image.

Removing The Parking Brake From A Chevrolet Silverado
Hit the rotor in the following areas

Once the rotor is off, check the condition of the inner rotor parking brake pad surface. If there is a deep scratch or gouge, it will be necessary to change the rotor.

4- Remove the handbrake shoe

The parking or parking brake shoe is a one-piece design that almost makes a circle around the center. It connects to the center in two places. The first is in the parking brake wheel cylinder. The second is on the metal clip attached to the bucket. They are on opposite sides of the parking brake shoe.

  • Using a flathead screwdriver, push the parking brake shoe away from the metal clip. This creates a gap between the metal clip and the inner side of the brake shoe. Then grab the shoe by one end connected to the wheel cylinder and rotate it out and away from the hub.
  • You will need to twist and angle the parking brake shoe to get it to move away from the hub.

5- Reinstall the parking brake shoes, rotors, calipers and wheels

Replace The Parking Brake On A Chevy Silverado
Place the bolts

To finish changing the parking brake of a Chevrolet Silverado, what this is is to reinstall everything.

  • Slide the parking brake shoe around and over the hub.
  • Find the metal clip again and place the inside of the shoe against the inside of the metal clip. This locks the shoe against the support plate preventing it from moving forward when the emergency brake is applied.
  • Then place the ends of the shoe into the slots on the sides of the wheel cylinder.
  • Now that the new shoe is installed, slide the rotor back on.
  • The caliper will slide back over the rotor. Move the caliper into the correct position to reinstall the two bolts that secure it to the hub.
  • Now reinstall the wheels and tighten the lug nuts.

After this your Silverado pickup’s parking brake should feel like new!

Necessary materials

  • Metric socket set or socket wrench (13mm to 21mm)
  • 1/2″ air or electric impact wrench
  • 1/2″ breaker bar (if impact wrench is not available)
  • flat head screwdriver
  • Wire or clamp

Tips

When jacking up the vehicle to remove the rear wheels it is best to use a block of wood between the jack stand and the frame rail so you can eliminate damage to the frame rail itself.

Leave a Comment