Steps To Change The Brake Rotors On A Chevrolet Silverado

Hi-ya! good morning, today i will created an article about Steps To Change The Brake Rotors On A Chevrolet Silverado

The brakes on a Chevy Silverado have parts that must be replaced over time to maintain the integrity of the brakes. here you will learn how to change the brake discs on a Chevrolet Silverado. Keep reading!

These discs must be replaced if they are worn beyond the minimum thickness; the minimum thickness is printed on the rotor, and a micrometer will measure the current thickness.

Since the brakes and their pads must be the same on both sides of the truck, it is necessary to change the two rotors or discs together; You also need to replace the Silverado’s brake pads at the same time.

How to change the brake discs on a Chevrolet Silverado?

It is convenient for you to check and change the parts as necessary. Brakes can emit a dust that may contain asbestos or other contaminants, so care must be taken when working with dusty brake parts. Dust can be removed or reduced by using a damp cloth or commercial cleaner to remove it.

Also, avoid grinding brake pads, sanding brake pads, and cleaning wheel brake parts with any compressed air or a dry brush. There are special tools that are recommended to complete the job.

The steps to follow to change the brake discs on a Chevrolet Silverado correctly are the following:

1- Remove the disks

The first part of this repair is the removal of the Chevy Silverado’s brake discs.

1. Siphon at least two-thirds of the brake fluid from the brake master cylinder reservoir using a turkey baster, syringe bottle, or other siphoning tool that has never been used before. Dispose of this fluid as permitted by the laws of your country or state.

2. Raise the front or rear of the truck and support it on a jack stand. Then remove the wheels.

3. Compress the caliper pistons back into their bores with a C-clamp. Observe the brake fluid level in the master cylinder reservoir as you compress the piston and siphon more fluid if necessary to prevent overflow .

4. Unscrew the brake caliper bolts with a wrench and remove the caliper; hang the clip from the frame with a strong wire; don’t let it hang from the hose.

5. Remove the brake pads from the caliper mounting bracket and discard them.

6. Unbolt and remove the caliper mounting bracket with the wrench.

7. Cut out the flanged washers installed on the wheel studs with a pair of cutters. Then slide the brake rotor off of the hub.

2- Installation of the brake discs

The other part of this job, and to finish changing the brake discs on a Chevrolet Silverado, is the installation process and checking that everything has gone well:

1. Mount the replacement brake disc onto the wheel studs. You will not need to install any replacement washers on the bolts if you removed any old ones.

2. Attach the caliper mounting bracket to the rotor, tightening the mounting bolts to 129 foot-pounds (221 foot-pounds on models other than the 1500) with a torque wrench.

3. Install replacement brake pads in the Silveradoon the caliper mounting bracket.

4. Connect the caliper to the mounting bracket and tighten the mounting bolts with the torque wrench (74 foot-pounds on a 1500, 80 for other models).

5. Reinstall the wheels and lower the truck after changing the discs that needed to be replaced.

6. Fill the brake master cylinder reservoir with new brake fluid.

7. Operate the brake pedal several times until it feels firmto re-seat the brake pads against the discs.

With these steps you will be able to change the brake discs on a Chevrolet Silverado when they need to be replaced. Remember that the brakes and the pads must be exactly the same on both sides of the vehicle, it is always necessary to change both discs together.

You can read: How to Turn Off the ABS Brake Lights on a Chevy Silverado

Tips

In case you just want to impress, then:

• Removing at least the wheels and calipers as described above will help you inspect the condition of the entire brake disc surface.

• For ease remember to remove the screw and then spray a little penetrating oil, let the rotor soak with a rubber mallet or tap hammer.

• You can make sure not to let the calipers dangle and tie them with string or wire, otherwise you risk damaging the brake line.

• You will also need to push the caliper to fit over the new rotor, when at this step don’t push them in as fast as you can as you will push dirt back into the system or master cylinder, this will cause other problems. So take it easy.

Items you will need

The tools and items to use are:

• Syringe to extract the liquid (preferably turkey)

• Brake discs or rotors

The brakes on a Chevy Silverado have parts that must be replaced over time to maintain the integrity of the brakes. here you will learn how to change the brake discs on a Chevrolet Silverado. Keep reading!

These discs must be replaced if they are worn beyond the minimum thickness; the minimum thickness is printed on the rotor, and a micrometer will measure the current thickness.

Since the brakes and their pads must be the same on both sides of the truck, it is necessary to change the two rotors or discs together; You also need to replace the Silverado’s brake pads at the same time.

How to change the brake discs on a Chevrolet Silverado?

It is convenient for you to check and change the parts as necessary. Brakes can emit a dust that may contain asbestos or other contaminants, so care must be taken when working with dusty brake parts. Dust can be removed or reduced by using a damp cloth or commercial cleaner to remove it.

Also, avoid grinding brake pads, sanding brake pads, and cleaning wheel brake parts with any compressed air or a dry brush. There are special tools that are recommended to complete the job.

The steps to follow to change the brake discs on a Chevrolet Silverado correctly are the following:

1- Remove the disks

The first part of this repair is the removal of the Chevy Silverado’s brake discs.

1. Siphon at least two-thirds of the brake fluid from the brake master cylinder reservoir using a turkey baster, syringe bottle, or other siphoning tool that has never been used before. Dispose of this fluid as permitted by the laws of your country or state.

2. Raise the front or rear of the truck and support it on a jack stand. Then remove the wheels.

3. Compress the caliper pistons back into their bores with a C-clamp. Observe the brake fluid level in the master cylinder reservoir as you compress the piston and siphon more fluid if necessary to prevent overflow .

4. Unscrew the brake caliper bolts with a wrench and remove the caliper; hang the clip from the frame with a strong wire; don’t let it hang from the hose.

5. Remove the brake pads from the caliper mounting bracket and discard them.

6. Unbolt and remove the caliper mounting bracket with the wrench.

7. Cut out the flanged washers installed on the wheel studs with a pair of cutters. Then slide the brake rotor off of the hub.

2- Installation of the brake discs

The other part of this job, and to finish changing the brake discs on a Chevrolet Silverado, is the installation process and checking that everything has gone well:

1. Mount the replacement brake disc onto the wheel studs. You will not need to install any replacement washers on the bolts if you removed any old ones.

2. Attach the caliper mounting bracket to the rotor, tightening the mounting bolts to 129 foot-pounds (221 foot-pounds on models other than the 1500) with a torque wrench.

3. Install replacement brake pads in the Silveradoon the caliper mounting bracket.

4. Connect the caliper to the mounting bracket and tighten the mounting bolts with the torque wrench (74 foot-pounds on a 1500, 80 for other models).

5. Reinstall the wheels and lower the truck after changing the discs that needed to be replaced.

6. Fill the brake master cylinder reservoir with new brake fluid.

7. Operate the brake pedal several times until it feels firmto re-seat the brake pads against the discs.

With these steps you will be able to change the brake discs on a Chevrolet Silverado when they need to be replaced. Remember that the brakes and the pads must be exactly the same on both sides of the vehicle, it is always necessary to change both discs together.

You can read: How to Turn Off the ABS Brake Lights on a Chevy Silverado

Tips

In case you just want to impress, then:

• Removing at least the wheels and calipers as described above will help you inspect the condition of the entire brake disc surface.

• For ease remember to remove the screw and then spray a little penetrating oil, let the rotor soak with a rubber mallet or tap hammer.

• You can make sure not to let the calipers dangle and tie them with string or wire, otherwise you risk damaging the brake line.

• You will also need to push the caliper to fit over the new rotor, when at this step don’t push them in as fast as you can as you will push dirt back into the system or master cylinder, this will cause other problems. So take it easy.

Items you will need

The tools and items to use are:

• Syringe to extract the liquid (preferably turkey)

• Brake discs or rotors