Programming Kia Soul Keyless Ignition System

Hi! good afternoon, at this time i will created an article about Programming Kia Soul Keyless Ignition System

Keyless ignition systems are an excellent standard option on many of the cars being sold today. This option allows the owner to open and close the vehicle doors while outside the vehicle. Various keyless remotes can also open the trunk or tailgate of the vehicle, but this time you will learn the steps to program the keyless ignition system of the Kia Soul.

This invention or improvement has replaced and optimized the way people insure their cars. However, when the battery in the remote dies, the steps for programming the controls can become very confusing. You should know that one of the most complicated operations for programming remote controls is in a Kia Soul car.

Programming the keyless ignition system of the Kia Soul

The steps you must follow to program the keyless ignition system of a Kia Soul vehicle are as follows:

  1. Open the hood of your soul.
  1. Locate the vehicle diagnostic cap and release the cap, the plug will be located at the rear of the battery on the driver’s side, but in the engine compartment. The cap on the plug says “Diagnosis“.
  1. Strip the two ends of the 22-gauge wire to reveal a half inch of bare copper.
  1. Put one end of the cable into port number 6 of the diagnostic connector, that port is the second port in the full row of ports next to the 4 port row, you should also study the Resources section for a complete diagram on the diagnostic port.
  1. Proceed to connect the other end of the cable to the positive terminal of the battery, this can be simply glued into a hole in the terminal; a permanent connection is not required.
  1. Sit in the driver’s seat of the car and turn the car’s ignition to the “ON” position. Do not start the vehicle.
  1. You must hold down the “LOCK” on the first remote for at least 1 second and then you should release, then proceed and repeat the same process for the second remote. If you are only programming one remote, press and hold the lock button on the remote for at least three seconds and then release it.If done correctly, the dashboard lights will turn off.
  1. Turn off the car when the dash lights go out and remove the cable from the battery and diagnostic terminal so you can finally test your remote.

You can also read about the: Kia Soul Power Window Problems.

warnings

If perhaps this process has not worked for you, you should contact a local distributor to grant you the corresponding process. Many cars require a computer download to program the remotes, which must be done by a dealer.

Programming Kia Soul Keyless Ignition System
Kia Soul en Paris

Keyless ignition systems are an excellent standard option on many of the cars being sold today. This option allows the owner to open and close the vehicle doors while outside the vehicle. Various keyless remotes can also open the trunk or tailgate of the vehicle, but this time you will learn the steps to program the keyless ignition system of the Kia Soul.

This invention or improvement has replaced and optimized the way people insure their cars. However, when the battery in the remote dies, the steps for programming the controls can become very confusing. You should know that one of the most complicated operations for programming remote controls is in a Kia Soul car.

Programming the keyless ignition system of the Kia Soul

The steps you must follow to program the keyless ignition system of a Kia Soul vehicle are as follows:

  1. Open the hood of your soul.
  1. Locate the vehicle diagnostic cap and release the cap, the plug will be located at the rear of the battery on the driver’s side, but in the engine compartment. The cap on the plug says “Diagnosis“.
  1. Strip the two ends of the 22-gauge wire to reveal a half inch of bare copper.
  1. Put one end of the cable into port number 6 of the diagnostic connector, that port is the second port in the full row of ports next to the 4 port row, you should also study the Resources section for a complete diagram on the diagnostic port.
  1. Proceed to connect the other end of the cable to the positive terminal of the battery, this can be simply glued into a hole in the terminal; a permanent connection is not required.
  1. Sit in the driver’s seat of the car and turn the car’s ignition to the “ON” position. Do not start the vehicle.
  1. You must hold down the “LOCK” on the first remote for at least 1 second and then you should release, then proceed and repeat the same process for the second remote. If you are only programming one remote, press and hold the lock button on the remote for at least three seconds and then release it.If done correctly, the dashboard lights will turn off.
  1. Turn off the car when the dash lights go out and remove the cable from the battery and diagnostic terminal so you can finally test your remote.

You can also read about the: Kia Soul Power Window Problems.

warnings

If perhaps this process has not worked for you, you should contact a local distributor to grant you the corresponding process. Many cars require a computer download to program the remotes, which must be done by a dealer.

Programming Kia Soul Keyless Ignition System
Kia Soul en Paris

Leave a Comment