How To Install A Wind Deflector On A BMW E46: + Tip!

Hi-ya! good afternoon, at this moment we will made an article about How To Install A Wind Deflector On A BMW E46: + Tip!

The BMW E46 is the body style line for BMW 3-series cars with a production date between 1999 and 2006, including BMW convertibles. A wind deflector prevents wind and debris from entering the passenger cabin in a convertible while the top is down. Read more and learn how to install a wind deflector on a BMW E46.

Installing a wind deflector on an E46 BMW 3 Series Convertible offers an interior upgrade and only takes 10-15 minutes.

How to Install a Wind Deflector on a BMW E46

Mount A Wind Deflector On A BMW E46
BMW E46 318ti

You must follow a series of steps to install a wind deflector on a BMW E46.

  1. Put down the convertible top, leaving the storage lid behind the rear seat headrests about 3 inches away. Locate a hole in the trim panels below the E46 rear seat driver and passenger side windows for post barrel bolt installation.
  1. Slide the barrel bolts on each side of the wind deflector to a vertical position. Tighten the thumbscrews under the bolts so they are tight enough to hold the bolts upright.
  1. Extends the barrel bolt out on the passenger side. Lock it in place with the handle facing up. Keep the driver’s side bolt in its original position.
  1. Extend the two rear brackets located at the rear of the baffle and tighten the thumbscrews. These brackets extend to fit under the convertible top that you raised in step 1.
  1. Stand on the driver’s side of the vehicle. Hold the wind deflector and insert the barrel stud you extended in step 3 into the passenger side hole noted in step 1.
  1. Lower the deflector so it lays flat in the rear seat area, with the top of the deflector pointing toward the rear seat. Put the rear brackets in place through the 3-inch opening in the storage lid for the convertible top.
  1. Align the driver’s side barrel bolt with the corresponding hole. Slide the barrel bolt into the hole and rotate it toward the front of the vehicle.
  1. Push back on the barrel bolts on each side to lock the wind deflector in place. Close the convertible top storage lid to lock the rear wind deflector brackets in place.

Advice

Fitting a wind deflector to an E46 BMW 3 Series Convertible will offer a huge improvement to the interior of the vehicle, remember you will be working with somewhat delicate materials so be careful.

The BMW E46 is the body style line for BMW 3-series cars with a production date between 1999 and 2006, including BMW convertibles. A wind deflector prevents wind and debris from entering the passenger cabin in a convertible while the top is down. Read more and learn how to install a wind deflector on a BMW E46.

Installing a wind deflector on an E46 BMW 3 Series Convertible offers an interior upgrade and only takes 10-15 minutes.

How to Install a Wind Deflector on a BMW E46

Mount A Wind Deflector On A BMW E46
BMW E46 318ti

You must follow a series of steps to install a wind deflector on a BMW E46.

  1. Put down the convertible top, leaving the storage lid behind the rear seat headrests about 3 inches away. Locate a hole in the trim panels below the E46 rear seat driver and passenger side windows for post barrel bolt installation.
  1. Slide the barrel bolts on each side of the wind deflector to a vertical position. Tighten the thumbscrews under the bolts so they are tight enough to hold the bolts upright.
  1. Extends the barrel bolt out on the passenger side. Lock it in place with the handle facing up. Keep the driver’s side bolt in its original position.
  1. Extend the two rear brackets located at the rear of the baffle and tighten the thumbscrews. These brackets extend to fit under the convertible top that you raised in step 1.
  1. Stand on the driver’s side of the vehicle. Hold the wind deflector and insert the barrel stud you extended in step 3 into the passenger side hole noted in step 1.
  1. Lower the deflector so it lays flat in the rear seat area, with the top of the deflector pointing toward the rear seat. Put the rear brackets in place through the 3-inch opening in the storage lid for the convertible top.
  1. Align the driver’s side barrel bolt with the corresponding hole. Slide the barrel bolt into the hole and rotate it toward the front of the vehicle.
  1. Push back on the barrel bolts on each side to lock the wind deflector in place. Close the convertible top storage lid to lock the rear wind deflector brackets in place.

Advice

Fitting a wind deflector to an E46 BMW 3 Series Convertible will offer a huge improvement to the interior of the vehicle, remember you will be working with somewhat delicate materials so be careful.

Leave a Comment