How To Fix Boot System Problems On A Rogue!

Hi! good night, this day i will created an article about How To Fix Boot System Problems On A Rogue!

The starting system on a Nissan Rogue consists of the battery, ignition relay switch, starter motor, and starter solenoid. If one of these components fails, your Nissan will not start. Fortunately, you can isolate and troubleshoot or fix boot system problems on a Roguechecking each of the components to quickly determine which component is causing your car to not start properly.

Boot System Problems on a Rogue: Solution

Here is a series of steps to solve the problems that occur in the starting system in a Nissan Rogue car:

  1. Connect the black lead from your multimeter to the negative terminal of your Nissan Rogue’s battery. Connect the red lead of the multimeter to the positive terminal of the battery and set the multimeter to “20V DC” and measure the battery output. If the battery puts out less than 12 volts of power, the engine may not start. Charge the battery until you read at least 12 volts of power on the multimeter, then try to start the Rogue.
  1. He turns on the headlights of his Nissan Rogue car and tries to start the vehicle. If the headlights do not dim, then it is very possible that the ignition relay is faulty. If the lights dim, the relay switch is working properly and the problem is elsewhere.
  1. Locate the starter motor and solenoid on the driver’s side transmission housing.. The starter mounts to the housing and the solenoid mounts to the top of the starter, locate the two metal connectors on the back of the solenoid. Both connectors have a cable attached to them.
  1. Place the blade of a screwdriver on both connectors at the same time. Signal the second person to turn on the ignition key for 10 seconds. The motor will not turn over because you shorted out the solenoid. However, the starter should fire. If it does and makes a soft humming sound, the starter is good and the solenoid is bad. If the starter motor does not fire or runs intermittently, the starter motor is faulty and the solenoid is most likely good.

In this way you will be able to detect the problem and find a solution to the failures and problems of the starting system in a Nissan Rogue vehicle.

Caveat

When the starter motor is tested, the solenoid is not being tested. If the starter motor is bad, it is possible that the solenoid is bad as well, however this is highly unlikely.

What will you need?

  • multimeter
  • Screwdriver
  • A second person to help
Boot System Failures on a Rogue
Nissan Rogue 2009

Don’t stop reading about: The Steps To Properly Replace A Rogue’s Thermostat

The starting system on a Nissan Rogue consists of the battery, ignition relay switch, starter motor, and starter solenoid. If one of these components fails, your Nissan will not start. Fortunately, you can isolate and troubleshoot or fix boot system problems on a Roguechecking each of the components to quickly determine which component is causing your car to not start properly.

Boot System Problems on a Rogue: Solution

Here is a series of steps to solve the problems that occur in the starting system in a Nissan Rogue car:

  1. Connect the black lead from your multimeter to the negative terminal of your Nissan Rogue’s battery. Connect the red lead of the multimeter to the positive terminal of the battery and set the multimeter to “20V DC” and measure the battery output. If the battery puts out less than 12 volts of power, the engine may not start. Charge the battery until you read at least 12 volts of power on the multimeter, then try to start the Rogue.
  1. He turns on the headlights of his Nissan Rogue car and tries to start the vehicle. If the headlights do not dim, then it is very possible that the ignition relay is faulty. If the lights dim, the relay switch is working properly and the problem is elsewhere.
  1. Locate the starter motor and solenoid on the driver’s side transmission housing.. The starter mounts to the housing and the solenoid mounts to the top of the starter, locate the two metal connectors on the back of the solenoid. Both connectors have a cable attached to them.
  1. Place the blade of a screwdriver on both connectors at the same time. Signal the second person to turn on the ignition key for 10 seconds. The motor will not turn over because you shorted out the solenoid. However, the starter should fire. If it does and makes a soft humming sound, the starter is good and the solenoid is bad. If the starter motor does not fire or runs intermittently, the starter motor is faulty and the solenoid is most likely good.

In this way you will be able to detect the problem and find a solution to the failures and problems of the starting system in a Nissan Rogue vehicle.

Caveat

When the starter motor is tested, the solenoid is not being tested. If the starter motor is bad, it is possible that the solenoid is bad as well, however this is highly unlikely.

What will you need?

  • multimeter
  • Screwdriver
  • A second person to help
Boot System Failures on a Rogue
Nissan Rogue 2009

Don’t stop reading about: The Steps To Properly Replace A Rogue’s Thermostat

Leave a Comment