How to Change the Windshield Washer Reservoir on a Chevy Silverado

Hi-ya! good afternoon, at this time i will made an article about How to Change the Windshield Washer Reservoir on a Chevy Silverado

Many owners do not keep their Silverado, especially if it is a work truck, as clean as they should, although it is vital to keep the windshield clean and not have wiper failure. Keep reading until the end and learn: How to Change the Windshield Washer Reservoir on a Chevy Silverado.

Fill the windshield washer fluid periodically and use it regularly. If you know that you just filled it and you realize that you have not run out of fluid, it is sure that there is a leak in the reservoir. You must find her and fix her.

How to Change the Windshield Washer Reservoir on a Chevy Silverado

Remove The Windshield Washer Reservoir On A Chevrolet Silverado
Chevrolet Silverado LS 2011

The windshield washer reservoir is a very important element of the system responsible for keeping the glass clean, since it stores the liquid that cleans the windshield of automobiles.

Windshield washer fluid, or washer fluid, is a fluid designed to remove dirt from the windshield (less often the rear windshield as well) of a car. In many modern cars, in addition to the windshields, the headlights can also be washed. The liquid is sprayed through special nozzles and cleaned with brushes..

It may interest you: Common Windshield Wiper Problems: Solutions & More

Here are the steps you need to take to change a faulty windshield washer reservoir on a Chevrolet Silverado.

  1. Buy a new windshield washer reservoir after finding the part number for your Chevy Silverado, which depends on the year of your truck. You can start your search online.
  1. Select a level surface to work on your Chevy Silverado. Make sure there is enough space. After parking your truck, turn off the engine and set the emergency brake, then get out of the Silverado. Now with the help of your right hand, insert it and pull the hood release actuator.
  1. Now go to the engine compartment by unhooking the auxiliary release latch under the hood. Raise the cover until the hydraulic lifter kicks in and opens the cover fully.
  1. Find the windshield washer reservoir. The reservoir on a Chevy Silverado usually has a black cap located in the lower right corner of the engine compartment. Also on the lid is a waterspout.
  1. Pour a little fluid into the reservoir to find the leak, and if it’s small, then sure you can patch it, on the other hand you can change the whole repository. Now proceed to disconnect the negative battery cable and wait for 2 minutes before starting work, in case your Chevy Silverado is equipped with air bags.
  1. Remove the wiper arms in one of three ways. If a spring clip is holding the wiper arms together and there is a release tab in the center, depress the tab and the arm will release. If there isn’t a tab, use a small lever to depress the spring and release the arm.
    • On the other hand, there should be a small release hole in the base and inserting a 1/8-inch drift pin into the access hole will release the locking device and allow you to easily remove the arm.
  1. Remove the top grille from the hood by gently pulling on the outside corners of the hood until you can release it. Then, using a screwdriver, disconnect the wire harness, washer hose, and sheet metal screws attached to the reservoir. After you’ve done this, simply lift up the windshield washer reservoir. Throw away all the stamps from the old tank; you will have to change them when you install the new reservoir.
  1. Install the new windshield washer reservoir in your Chevrolet Silverado fitting the tank and reconnecting the wiring harness, windshield washer hose and sheet metal bolts then replacing the seals.
  1. Put the upper hood grille back in place. Then, reassemble the wiper arms by reversing the order in step 6. Reconnect the battery again and fill the new reservoir with windshield washer fluid.

These were all the steps to change the windshield washer reservoir on a Chevrolet Silverado. Remember that if you can cover the leak of the old tank it is not necessary Buy a new one.

You may be interested in: 10 Steps To Clean Your Window Washer Reservoir

Tips

When you are working on this section of the vehicle you must take into account:

  • Place a drain bucket under the reservoir to catch any washer solvent that may leak out.
  • You can buy premixed windshield washer fluid (diluted window cleaner) or make your own by adding about three cups of window cleaner to every gallon of distilled water.

warnings

You must be careful with the following:

  • Prevent frozen fluid in the windshield washer reservoir and washer lines by using a winter-weather fluid that includes both washer and ice remover.

Also read about: How to Change the Windshield Wiper Motor on a Chevy Silverado

Items you will need

The items and tools to use on this occasion are:

  • windshield washer reservoir
  • 1/8 inch drift bolt

Many owners do not keep their Silverado, especially if it is a work truck, as clean as they should, although it is vital to keep the windshield clean and not have wiper failure. Keep reading until the end and learn: How to Change the Windshield Washer Reservoir on a Chevy Silverado.

Fill the windshield washer fluid periodically and use it regularly. If you know that you just filled it and you realize that you have not run out of fluid, it is sure that there is a leak in the reservoir. You must find her and fix her.

How to Change the Windshield Washer Reservoir on a Chevy Silverado

Remove The Windshield Washer Reservoir On A Chevrolet Silverado
Chevrolet Silverado LS 2011

The windshield washer reservoir is a very important element of the system responsible for keeping the glass clean, since it stores the liquid that cleans the windshield of automobiles.

Windshield washer fluid, or washer fluid, is a fluid designed to remove dirt from the windshield (less often the rear windshield as well) of a car. In many modern cars, in addition to the windshields, the headlights can also be washed. The liquid is sprayed through special nozzles and cleaned with brushes..

It may interest you: Common Windshield Wiper Problems: Solutions & More

Here are the steps you need to take to change a faulty windshield washer reservoir on a Chevrolet Silverado.

  1. Buy a new windshield washer reservoir after finding the part number for your Chevy Silverado, which depends on the year of your truck. You can start your search online.
  1. Select a level surface to work on your Chevy Silverado. Make sure there is enough space. After parking your truck, turn off the engine and set the emergency brake, then get out of the Silverado. Now with the help of your right hand, insert it and pull the hood release actuator.
  1. Now go to the engine compartment by unhooking the auxiliary release latch under the hood. Raise the cover until the hydraulic lifter kicks in and opens the cover fully.
  1. Find the windshield washer reservoir. The reservoir on a Chevy Silverado usually has a black cap located in the lower right corner of the engine compartment. Also on the lid is a waterspout.
  1. Pour a little fluid into the reservoir to find the leak, and if it’s small, then sure you can patch it, on the other hand you can change the whole repository. Now proceed to disconnect the negative battery cable and wait for 2 minutes before starting work, in case your Chevy Silverado is equipped with air bags.
  1. Remove the wiper arms in one of three ways. If a spring clip is holding the wiper arms together and there is a release tab in the center, depress the tab and the arm will release. If there isn’t a tab, use a small lever to depress the spring and release the arm.
    • On the other hand, there should be a small release hole in the base and inserting a 1/8-inch drift pin into the access hole will release the locking device and allow you to easily remove the arm.
  1. Remove the top grille from the hood by gently pulling on the outside corners of the hood until you can release it. Then, using a screwdriver, disconnect the wire harness, washer hose, and sheet metal screws attached to the reservoir. After you’ve done this, simply lift up the windshield washer reservoir. Throw away all the stamps from the old tank; you will have to change them when you install the new reservoir.
  1. Install the new windshield washer reservoir in your Chevrolet Silverado fitting the tank and reconnecting the wiring harness, windshield washer hose and sheet metal bolts then replacing the seals.
  1. Put the upper hood grille back in place. Then, reassemble the wiper arms by reversing the order in step 6. Reconnect the battery again and fill the new reservoir with windshield washer fluid.

These were all the steps to change the windshield washer reservoir on a Chevrolet Silverado. Remember that if you can cover the leak of the old tank it is not necessary Buy a new one.

You may be interested in: 10 Steps To Clean Your Window Washer Reservoir

Tips

When you are working on this section of the vehicle you must take into account:

  • Place a drain bucket under the reservoir to catch any washer solvent that may leak out.
  • You can buy premixed windshield washer fluid (diluted window cleaner) or make your own by adding about three cups of window cleaner to every gallon of distilled water.

warnings

You must be careful with the following:

  • Prevent frozen fluid in the windshield washer reservoir and washer lines by using a winter-weather fluid that includes both washer and ice remover.

Also read about: How to Change the Windshield Wiper Motor on a Chevy Silverado

Items you will need

The items and tools to use on this occasion are:

  • windshield washer reservoir
  • 1/8 inch drift bolt

Leave a Comment