How to Change the Windshield Washer Pump on a Ford Fiesta

Hello! good morning, today we will made an article about How to Change the Windshield Washer Pump on a Ford Fiesta

The Ford Fiesta’s windshield washer pump releases fluid to clean the windshield. The spray increases visibility by removing debris. When the windshield washer pump motor begins to wear out or stops working, it no longer supplies fluid to the windshield. In that case, it must be replaced. Continue reading until the end and discover how to change the windshield washer pump on a ford fiesta.

Removing the old pump and replacing it with a new one is a quick job (approximately one to two hours) that requires only a few tools.

Change the windshield washer pump on a Ford Fiesta

The steps that you must carry out to change the windshield washer pump of the Fiesta successfully are the following:

Removing A Wiper Motor On A Fiesta
Ford Fiesta de Rally
  1. Pull the lever located under the steering panel to release the hood. Raise the hood and open it with the suspension bar located on the right side of the engine compartment.
  1. Locate the washer pump on the driver’s side of the engine cavity. It is a clear plastic bottle slightly in front of the tire.
  1. Access the pump by removing the driver’s side front fender. Unscrew the three bolts from the top of the front fender in the engine cavity. Use a socket wrench to remove the four fender bolts at the front of the driver’s side tire. Lift the fender up and remove the liner from the tire to expose the entire washer fluid reservoir.
  1. Unhook the power cord by pulling on the tabs. Pull out the suction hose. Remove the bolts holding the tank in place with a socket wrench. Now take out the tank.
  1. Holds the washer pump (small black device at the bottom) and pull it to remove it from the tank. To change the Ford Fiesta’s windshield washer pump, use a flathead screwdriver to pry the rubber grommet free from the reservoir. Place the grommet in the same location on the new tank. Put a small amount of lubricant on the inside of the washer. Push the washer pump back into place.
  1. Reconnect the power cord and intake hose to the pump. Slide the reservoir back into place and reattach the bolts. Also put the fender back on and reattach all screws and bolts removed in step 3.
  1. Unscrew the cap on the reservoir and fill it with fluid until it reaches the “Max” line.
  1. Hold the hood of the Ford Fiesta and release the suspension bar. Lower the hood slowly and push it down to latch it.

It may interest you: The most common problems in a windshield wiper

Tips

To be able to change the windshield washer pump in a Ford Fiesta you must carry out these steps as we explain here, if you are not sure about doing it on your own, ask someone to help you.

Explanatory video:

And no water coming out of your windshield wipersMost likely it’s a pump problem. Learn in this video how our friend changes the windshield washer pump of a Ford Fiesta vehicle.

The Ford Fiesta’s windshield washer pump releases fluid to clean the windshield. The spray increases visibility by removing debris. When the windshield washer pump motor begins to wear out or stops working, it no longer supplies fluid to the windshield. In that case, it must be replaced. Continue reading until the end and discover how to change the windshield washer pump on a ford fiesta.

Removing the old pump and replacing it with a new one is a quick job (approximately one to two hours) that requires only a few tools.

Change the windshield washer pump on a Ford Fiesta

The steps that you must carry out to change the windshield washer pump of the Fiesta successfully are the following:

Removing A Wiper Motor On A Fiesta
Ford Fiesta de Rally
  1. Pull the lever located under the steering panel to release the hood. Raise the hood and open it with the suspension bar located on the right side of the engine compartment.
  1. Locate the washer pump on the driver’s side of the engine cavity. It is a clear plastic bottle slightly in front of the tire.
  1. Access the pump by removing the driver’s side front fender. Unscrew the three bolts from the top of the front fender in the engine cavity. Use a socket wrench to remove the four fender bolts at the front of the driver’s side tire. Lift the fender up and remove the liner from the tire to expose the entire washer fluid reservoir.
  1. Unhook the power cord by pulling on the tabs. Pull out the suction hose. Remove the bolts holding the tank in place with a socket wrench. Now take out the tank.
  1. Holds the washer pump (small black device at the bottom) and pull it to remove it from the tank. To change the Ford Fiesta’s windshield washer pump, use a flathead screwdriver to pry the rubber grommet free from the reservoir. Place the grommet in the same location on the new tank. Put a small amount of lubricant on the inside of the washer. Push the washer pump back into place.
  1. Reconnect the power cord and intake hose to the pump. Slide the reservoir back into place and reattach the bolts. Also put the fender back on and reattach all screws and bolts removed in step 3.
  1. Unscrew the cap on the reservoir and fill it with fluid until it reaches the “Max” line.
  1. Hold the hood of the Ford Fiesta and release the suspension bar. Lower the hood slowly and push it down to latch it.

It may interest you: The most common problems in a windshield wiper

Tips

To be able to change the windshield washer pump in a Ford Fiesta you must carry out these steps as we explain here, if you are not sure about doing it on your own, ask someone to help you.

Explanatory video:

And no water coming out of your windshield wipersMost likely it’s a pump problem. Learn in this video how our friend changes the windshield washer pump of a Ford Fiesta vehicle.

Leave a Comment