Hi! good afternoon, at this time i will made an article about How To Change The Thermostat In A Ford Windstar Step By Step!
The vast majority of engine overheating issues are due to a bad thermostat, rather than an issue with the radiator itself. This time we will explain how to change the thermostat in a ford windstaryou just have to follow a series of specific steps.
The thermostat is a device that works as a switch to prevent the coolant from the radiator from running through the engine until it reaches the standard temperature when it is started.
A bad thermostat usually gets stuck in a closed position, causing the engine to overheat quickly. Fortunately, replacement thermostats are very inexpensive, and replacing the thermostat on a Ford Windstar car is simple.
How to Change the Thermostat on a Ford Windstar
To change the thermostat in a Ford Windstar car you must follow these steps:
- You must first remove the radiator cap, and then remove the drain cock from the lower area of the radiator with the help of a wrench so that you can drain the radiator.
- Now remove the mounting hose from the airbox; You should know that the airbox hose is a large, black plastic hose that runs from the airbox on the driver’s side of the engine split to the front area of the engine. This hose is connected to the front of the engine and to the black box with a single clamp on each end of the hose. Then loosen the two clamps with the help of a flat-head screwdriver, and then pull the hose in order to separate it from the engine and isolate it from the box.
- From the radiator you must trace the upper hose of the same to where you see that the hose enters the engine. The metal fragment that the hose is holding on to on the engine is the thermostat housing. As the name implies, the thermostat is located within such a frame or casing.
- Now you have to loosen with the help of a screwdriver the clamp that is responsible for retaining the upper radiator hose to the engine itself, and quickly pull the radiator hose away from the engine to detach it from the thermostat site.
- Isolate the two bolts (or nuts) holding the thermostat housing to the engine with a lug wrench, then remove the housing from the engine to access the thermostat. Then you just have to remove the thermostat from the engine.
- Put the new thermostat in the engine, it should be with the spring located on one side of the thermostat facing the engine. Now remove the gasket from the back of the thermostat housing and apply some gasket sealant to both sides of the new thermostat housing gasket. Lower the thermostat housing over the thermostat, then continue by installing and tightening the two thermostat housing retaining bolts with an open-end wrench.
- Put force on the radiator hose at the thermostat location, and now tighten the hose clamp using a screwdriver.
- Locate the air box assembly hose where it should go, and press the opposite end of the hose onto the engine. Next is to tighten the two hose clamps with a flat head screwdriver.
- Finally place and tighten the radiator drain cock with a wrench and allow at least three hours for the joint sealant to harden. Next is to fill the radiator with antifreeze and install the radiator cap to finish the job.
Items you will need
The items you will need to change the thermostat in a Ford Windstar are the following:
The vast majority of engine overheating issues are due to a bad thermostat, rather than an issue with the radiator itself. This time we will explain how to change the thermostat in a ford windstaryou just have to follow a series of specific steps.
The thermostat is a device that works as a switch to prevent the coolant from the radiator from running through the engine until it reaches the standard temperature when it is started.
A bad thermostat usually gets stuck in a closed position, causing the engine to overheat quickly. Fortunately, replacement thermostats are very inexpensive, and replacing the thermostat on a Ford Windstar car is simple.
How to Change the Thermostat on a Ford Windstar
To change the thermostat in a Ford Windstar car you must follow these steps:
- You must first remove the radiator cap, and then remove the drain cock from the lower area of the radiator with the help of a wrench so that you can drain the radiator.
- Now remove the mounting hose from the airbox; You should know that the airbox hose is a large, black plastic hose that runs from the airbox on the driver’s side of the engine split to the front area of the engine. This hose is connected to the front of the engine and to the black box with a single clamp on each end of the hose. Then loosen the two clamps with the help of a flat-head screwdriver, and then pull the hose in order to separate it from the engine and isolate it from the box.
- From the radiator you must trace the upper hose of the same to where you see that the hose enters the engine. The metal fragment that the hose is holding on to on the engine is the thermostat housing. As the name implies, the thermostat is located within such a frame or casing.
- Now you have to loosen with the help of a screwdriver the clamp that is responsible for retaining the upper radiator hose to the engine itself, and quickly pull the radiator hose away from the engine to detach it from the thermostat site.
- Isolate the two bolts (or nuts) holding the thermostat housing to the engine with a lug wrench, then remove the housing from the engine to access the thermostat. Then you just have to remove the thermostat from the engine.
- Put the new thermostat in the engine, it should be with the spring located on one side of the thermostat facing the engine. Now remove the gasket from the back of the thermostat housing and apply some gasket sealant to both sides of the new thermostat housing gasket. Lower the thermostat housing over the thermostat, then continue by installing and tightening the two thermostat housing retaining bolts with an open-end wrench.
- Put force on the radiator hose at the thermostat location, and now tighten the hose clamp using a screwdriver.
- Locate the air box assembly hose where it should go, and press the opposite end of the hose onto the engine. Next is to tighten the two hose clamps with a flat head screwdriver.
- Finally place and tighten the radiator drain cock with a wrench and allow at least three hours for the joint sealant to harden. Next is to fill the radiator with antifreeze and install the radiator cap to finish the job.
Items you will need
The items you will need to change the thermostat in a Ford Windstar are the following:
