Hi! good morning, this day we will write an article about How to Change the Starter Motor on a Ford Expedition Step By Step
If your Ford Expedition does not start, and the problem is the starter motor, you should know that there are a couple of solutions. But if you can start your Expedition, the problem would be with the battery or the alternator. Stay until the end and discover here how to change the starter on a ford expedition.
One of the most frequent problems that can occur in the life of a vehicle is a bad start, from which the Ford Expedition is not exempt. It is important to determine whether or not it is a bad starter motor that is preventing the vehicle from turning. That is why you must be sure that the starter motor is failing.
Steps to change the starter on a Ford Expedition
If the starter doesn’t work, then to fix this problem you need to change the starter on your Ford Expedition. The good thing about this bad situation is that replacing the starter motor is an action that most mechanics can easily perform.
Well, in case you want to do this job yourself, here are the steps to change the starter on a Ford Expedition:
1- Locate the starter motor in your Expedition.
You should trace your positive battery cable until you notice a split. One of the branches of the cable goes to the alternator and the other is the one that connects to the starter motor, which is about half the size of a football.
You should know that the starter motor is made up of two pieces with a cylindrical shape and glued together, but one of the cylinders is small and the other is large. Usually, the starter motor is located between the transmission and the engine. You can look at the bottom of your Expedition, also in the area under the air intake manifold.
2- Raise the vehicle
Use a floor jack and also stands to help lift the Expedition if the starter motor is located under the engine. Support one side of the chassis next to the driver’s side front door with the jack and put a jack stand to support the chassis.
Repeat the process again but on the front passenger side. You must ensure that all four legs of each cat are firmly on the ground.
3- Disconnect the negative battery cable.
This is for your safety, since the possibility of electrocution is automatically ruled out, and you must also disconnect the battery from the cooling fan, which can sometimes be activated even when the car is off.
4- Make your way to the starter motor
You must expose the starter motor of your Ford Expedition if any part gets in the way that does not allow you to access it. For example, there is a chance that you may need to remove the air intake manifold on certain models and years of this model Ford vehicle.
5- Disconnect the starter motor
Now you need to disconnect the electrical connection tab, which leads to the starter or starter motor. You may also need to temporarily push out some electrical wires and surrounding wiring so that you have the necessary work space to easily remove the starter. If you’re having a bit of trouble disengaging the tab, use a flat-blade screwdriver to gently separate the two pieces.
Unscrew the copper screw that holds the electrical cable of the starter motor in its respective place.. This will give you more room to work with to separate the starter motor from the engine.
Remove the bolts or screw that link the starter motor to the vehicle’s flywheel. If the bolts are too tight or stuck, you may need to use a torque wrench for extra leverage. Normally, there are two bolts that hold the starter motor in place. However, depending on the model, there may be as many as three bolts.
6- Remove the damaged starter motor and replace it with a new one
It’s time for you to remove the starter motor and change it for the new one. Take care to secure the starter motor with the two or three bolts you removed earlier. If you notice that the bolts are not tightened, you must force them to go into place, there is a possibility that you are not correctly aligning the part with the flywheel. If this happens, you need to unscrew the bolts and put the starter back on again.
You must reattach the electrical connection tab which is the one that leads to the new starter motor and again reattach the negative battery terminal cable. Turn the key of the Expedition to see if it already starts with that.
Install any other parts back in place, such as the hoses or the air intake manifold itself, anything that was removed to gain access to the starter motor. If you may have had to raise the Expedition on some jack stands, lower it to the ground following the reverse process you used to raise it in step 2.
Items you will need
The tools and things that you are going to need to change the starter on a Ford Expedition are the following:
If your Ford Expedition does not start, and the problem is the starter motor, you should know that there are a couple of solutions. But if you can start your Expedition, the problem would be with the battery or the alternator. Stay until the end and discover here how to change the starter on a ford expedition.
One of the most frequent problems that can occur in the life of a vehicle is a bad start, from which the Ford Expedition is not exempt. It is important to determine whether or not it is a bad starter motor that is preventing the vehicle from turning. That is why you must be sure that the starter motor is failing.
Steps to change the starter on a Ford Expedition
If the starter doesn’t work, then to fix this problem you need to change the starter on your Ford Expedition. The good thing about this bad situation is that replacing the starter motor is an action that most mechanics can easily perform.
Well, in case you want to do this job yourself, here are the steps to change the starter on a Ford Expedition:
1- Locate the starter motor in your Expedition.
You should trace your positive battery cable until you notice a split. One of the branches of the cable goes to the alternator and the other is the one that connects to the starter motor, which is about half the size of a football.
You should know that the starter motor is made up of two pieces with a cylindrical shape and glued together, but one of the cylinders is small and the other is large. Usually, the starter motor is located between the transmission and the engine. You can look at the bottom of your Expedition, also in the area under the air intake manifold.
2- Raise the vehicle
Use a floor jack and also stands to help lift the Expedition if the starter motor is located under the engine. Support one side of the chassis next to the driver’s side front door with the jack and put a jack stand to support the chassis.
Repeat the process again but on the front passenger side. You must ensure that all four legs of each cat are firmly on the ground.
3- Disconnect the negative battery cable.
This is for your safety, since the possibility of electrocution is automatically ruled out, and you must also disconnect the battery from the cooling fan, which can sometimes be activated even when the car is off.
4- Make your way to the starter motor
You must expose the starter motor of your Ford Expedition if any part gets in the way that does not allow you to access it. For example, there is a chance that you may need to remove the air intake manifold on certain models and years of this model Ford vehicle.
5- Disconnect the starter motor
Now you need to disconnect the electrical connection tab, which leads to the starter or starter motor. You may also need to temporarily push out some electrical wires and surrounding wiring so that you have the necessary work space to easily remove the starter. If you’re having a bit of trouble disengaging the tab, use a flat-blade screwdriver to gently separate the two pieces.
Unscrew the copper screw that holds the electrical cable of the starter motor in its respective place.. This will give you more room to work with to separate the starter motor from the engine.
Remove the bolts or screw that link the starter motor to the vehicle’s flywheel. If the bolts are too tight or stuck, you may need to use a torque wrench for extra leverage. Normally, there are two bolts that hold the starter motor in place. However, depending on the model, there may be as many as three bolts.
6- Remove the damaged starter motor and replace it with a new one
It’s time for you to remove the starter motor and change it for the new one. Take care to secure the starter motor with the two or three bolts you removed earlier. If you notice that the bolts are not tightened, you must force them to go into place, there is a possibility that you are not correctly aligning the part with the flywheel. If this happens, you need to unscrew the bolts and put the starter back on again.
You must reattach the electrical connection tab which is the one that leads to the new starter motor and again reattach the negative battery terminal cable. Turn the key of the Expedition to see if it already starts with that.
Install any other parts back in place, such as the hoses or the air intake manifold itself, anything that was removed to gain access to the starter motor. If you may have had to raise the Expedition on some jack stands, lower it to the ground following the reverse process you used to raise it in step 2.
Items you will need
The tools and things that you are going to need to change the starter on a Ford Expedition are the following:
