How To Change The Serpentine Belt Of A Toyota RAV4: 7 Steps!

Hello! good night, today i will write an article about How To Change The Serpentine Belt Of A Toyota RAV4: 7 Steps!

Toyota RAV4 models have a belt that is responsible for controlling all the accessories in the front area of ​​the engine. The serpentine belt is driven by the crankshaft pulley. Every time the crankshaft pulley turns, the serpentine belt slips around each of the attached pulleys. Read on and learn how to change the serpentine belt on a toyota rav4.

The serpentine belt has ribs on the inside of the belt that travel inside the grooves in each pulley. When these ribs or teeth begin to crack, the serpentine belt will need to be replaced.

Steps to change the serpentine belt on a Toyota RAV4

Replace RAV4 Serpentine Belt
Toyota RAV4 Excel HEV CVT 2.5 2019

The steps you must follow to correctly remove and replace the serpentine belt on a Toyota RAV4 are as follows:

  1. Open the hood of the Toyota RAV4 and before that, park the car in a good place.
  1. Inspect the top of the plastic screen around the radiator for a serpentine belt routing diagram.. The snake strap routing diagram will give you the routing directions for the new snake strap. If you can’t find or locate the serpentine belt routing diagram, draw the old belt routing on a piece of paper.
  1. Locate the tensioner that keeps the serpentine belt tight. The tensioner on Toyota RAV4 models is located at the front of the engine, in the center. You will be able to see a small bolt head in the center of the idler pulley.
  1. Turn the idler pulley clockwise with the 1/2-inch cutter bar and socket. This will loosen the serpentine belt from the pulleys. Remove the belt from each of the pulleys and remove the belt from the engine compartment.
  1. Place the new serpentine belt around each of the pulleys, starting with the crankshaft pulley.. Turn the idler pulley clockwise again with the 1/2-inch cutter bar and socket. Loop the serpentine belt around the tensioner pulley, then slowly release the tensioner so you can get the slack out of the belt.
  1. Start the Toyota RAV4 and watch the serpentine belt while the engine is running for about 30 seconds so you can make sure the belt stays inside each accessory pulley.
  1. Finally, it only remains to turn off the engine and close the hood.

With these steps you will be able to change the serpentine belt of a Toyota RAV4 satisfactorily, remember to follow these instructions to the letter.

How to Remove the Serpentine Belt From a RAV4
Toyota RAV4 EV second generation

Toyota RAV4 models have a belt that is responsible for controlling all the accessories in the front area of ​​the engine. The serpentine belt is driven by the crankshaft pulley. Every time the crankshaft pulley turns, the serpentine belt slips around each of the attached pulleys. Read on and learn how to change the serpentine belt on a toyota rav4.

The serpentine belt has ribs on the inside of the belt that travel inside the grooves in each pulley. When these ribs or teeth begin to crack, the serpentine belt will need to be replaced.

Steps to change the serpentine belt on a Toyota RAV4

Replace RAV4 Serpentine Belt
Toyota RAV4 Excel HEV CVT 2.5 2019

The steps you must follow to correctly remove and replace the serpentine belt on a Toyota RAV4 are as follows:

  1. Open the hood of the Toyota RAV4 and before that, park the car in a good place.
  1. Inspect the top of the plastic screen around the radiator for a serpentine belt routing diagram.. The snake strap routing diagram will give you the routing directions for the new snake strap. If you can’t find or locate the serpentine belt routing diagram, draw the old belt routing on a piece of paper.
  1. Locate the tensioner that keeps the serpentine belt tight. The tensioner on Toyota RAV4 models is located at the front of the engine, in the center. You will be able to see a small bolt head in the center of the idler pulley.
  1. Turn the idler pulley clockwise with the 1/2-inch cutter bar and socket. This will loosen the serpentine belt from the pulleys. Remove the belt from each of the pulleys and remove the belt from the engine compartment.
  1. Place the new serpentine belt around each of the pulleys, starting with the crankshaft pulley.. Turn the idler pulley clockwise again with the 1/2-inch cutter bar and socket. Loop the serpentine belt around the tensioner pulley, then slowly release the tensioner so you can get the slack out of the belt.
  1. Start the Toyota RAV4 and watch the serpentine belt while the engine is running for about 30 seconds so you can make sure the belt stays inside each accessory pulley.
  1. Finally, it only remains to turn off the engine and close the hood.

With these steps you will be able to change the serpentine belt of a Toyota RAV4 satisfactorily, remember to follow these instructions to the letter.

How to Remove the Serpentine Belt From a RAV4
Toyota RAV4 EV second generation

Leave a Comment