How to Change the Rear Brake Pads on a Mazda 3

Hi-ya! good afternoon, today we will created an article about How to Change the Rear Brake Pads on a Mazda 3

The Mazda 3 comes equipped with anti-lock disc brakes on all wheels. The front brakes take the brunt of braking and often need to be replaced more frequently than the rear pads. Although here we are going to indicate how to change the rear brake pads on a Mazda 3.

Inspect your rear brakes regularly before wear indicators start to seep into your rear brake rotors. Replacing the rear brake pads on time will not only ensure safe driving, but also save on the cost of repairing or replacing the rotors.

Steps to change the rear brake pads on a Mazda 3

To change the rear brake pads of your Mazda 3 car, just follow the steps below:

Change Rear Brake Pads On A Mazda 3
Mazda 3 MPS year 2008
  1. Park the Mazda on a flat surface. Leave enough room for you to work on both sides of the vehicle. Open the hood by pulling the hood release lever under the dashboard or on the car’s dashboard on the driver’s side of the vehicle.
  1. Raise the hood of the Mazda3 and remove the master cylinder cover located near the right side of the engine.. Withdraw half of the brake fluid from the container with a syringe. You will need room in the reservoir for the brake fluid that will flow back as a result of the caliper pistons opening on the rear brakes. Place the cap loosely on the mask cylinder.
  1. Then you need to loosen the lug nuts on the rear wheels with the lug wrench.
  1. Place a jack under the frame at the rear of the vehicle. Raise the rear of the car and support it with at least two jack stands. Place the supports under the trucks to get the best base of support.
  1. Remove the studs and remove the rear wheels from the vehicle.
  1. Remove the spring clips from the caliper with a pair of needle-nose pliers.
  1. Remove the dust caps from the two caliper pins. The caps can be removed by hand or with the help of a flathead screwdriver.
  1. Remove the two caliper pins with a 7-millimeter Allen wrench.
  1. Lift the caliper off the rear rotor and remove the brake pad connected to the caliper piston by a thin metal clip. Slide the caliper pad by hand or use a flathead screwdriver to pry it out of the caliper.
  1. Slide the outer brake pad from the caliper bridge. The outer pad slides off the bridge with little force.
  1. Check the brake assembly for wear and/or damage. Replace or repair any of the brake components that require service.
  1. Place the piston compression tool in the caliper and thread the piston into the side of the caliper. Remove or detach the tool from the caliper once the vehicle’s rear piston has fully opened to get the new, larger brake pads.
  1. Apply brake grease to the back panels of the new brake pads.
  1. Slide the rear brake pad into the caliper clips (next to the piston).
  1. Then place the outer piston in the grooves of the caliper bridge.
  1. Put the caliper back on the caliper bridge and rotor. Replace the caliper pins and screw them in with the 7-millimeter Allen wrench.
  1. Repeat the replacement process (provided for in steps 6 through 16) for the brake pads on the opposite wheel hub.
  1. Put the rear wheels back on the wheel studs and screw on the lugs by hand.
  1. Raise the rear of your Mazda 3 and remove the jack stands from under the axles.. Lower the rear tires to the ground and tighten the lug nuts with the lug wrench.
  1. Lift off the master cylinder cap and place a funnel in the reservoir, then fill the reservoir with DOT-3 brake fluid. Next you must remove the funnel and again put the master cylinder cover back on.
  1. close the hood.
  1. Start the Mazda 3 engine. Press the brake pedal repeatedly until the pedal response returns to normal. The first depressions will offer little resistance. As the brake fluid returns the caliper piston to the correct position, the pedal response will normalize.

Tips

Carrying out all these steps to the letter you will be able to change the rear brake pads of your Mazda 3 without problems. Remember that you must replace the brake pads in time to avoid major problems.

Replace Rear Brake Pads On A Mazda 3
Great Mazda 3 Sedan

The Mazda 3 comes equipped with anti-lock disc brakes on all wheels. The front brakes take the brunt of braking and often need to be replaced more frequently than the rear pads. Although here we are going to indicate how to change the rear brake pads on a Mazda 3.

Inspect your rear brakes regularly before wear indicators start to seep into your rear brake rotors. Replacing the rear brake pads on time will not only ensure safe driving, but also save on the cost of repairing or replacing the rotors.

Steps to change the rear brake pads on a Mazda 3

To change the rear brake pads of your Mazda 3 car, just follow the steps below:

Change Rear Brake Pads On A Mazda 3
Mazda 3 MPS year 2008
  1. Park the Mazda on a flat surface. Leave enough room for you to work on both sides of the vehicle. Open the hood by pulling the hood release lever under the dashboard or on the car’s dashboard on the driver’s side of the vehicle.
  1. Raise the hood of the Mazda3 and remove the master cylinder cover located near the right side of the engine.. Withdraw half of the brake fluid from the container with a syringe. You will need room in the reservoir for the brake fluid that will flow back as a result of the caliper pistons opening on the rear brakes. Place the cap loosely on the mask cylinder.
  1. Then you need to loosen the lug nuts on the rear wheels with the lug wrench.
  1. Place a jack under the frame at the rear of the vehicle. Raise the rear of the car and support it with at least two jack stands. Place the supports under the trucks to get the best base of support.
  1. Remove the studs and remove the rear wheels from the vehicle.
  1. Remove the spring clips from the caliper with a pair of needle-nose pliers.
  1. Remove the dust caps from the two caliper pins. The caps can be removed by hand or with the help of a flathead screwdriver.
  1. Remove the two caliper pins with a 7-millimeter Allen wrench.
  1. Lift the caliper off the rear rotor and remove the brake pad connected to the caliper piston by a thin metal clip. Slide the caliper pad by hand or use a flathead screwdriver to pry it out of the caliper.
  1. Slide the outer brake pad from the caliper bridge. The outer pad slides off the bridge with little force.
  1. Check the brake assembly for wear and/or damage. Replace or repair any of the brake components that require service.
  1. Place the piston compression tool in the caliper and thread the piston into the side of the caliper. Remove or detach the tool from the caliper once the vehicle’s rear piston has fully opened to get the new, larger brake pads.
  1. Apply brake grease to the back panels of the new brake pads.
  1. Slide the rear brake pad into the caliper clips (next to the piston).
  1. Then place the outer piston in the grooves of the caliper bridge.
  1. Put the caliper back on the caliper bridge and rotor. Replace the caliper pins and screw them in with the 7-millimeter Allen wrench.
  1. Repeat the replacement process (provided for in steps 6 through 16) for the brake pads on the opposite wheel hub.
  1. Put the rear wheels back on the wheel studs and screw on the lugs by hand.
  1. Raise the rear of your Mazda 3 and remove the jack stands from under the axles.. Lower the rear tires to the ground and tighten the lug nuts with the lug wrench.
  1. Lift off the master cylinder cap and place a funnel in the reservoir, then fill the reservoir with DOT-3 brake fluid. Next you must remove the funnel and again put the master cylinder cover back on.
  1. close the hood.
  1. Start the Mazda 3 engine. Press the brake pedal repeatedly until the pedal response returns to normal. The first depressions will offer little resistance. As the brake fluid returns the caliper piston to the correct position, the pedal response will normalize.

Tips

Carrying out all these steps to the letter you will be able to change the rear brake pads of your Mazda 3 without problems. Remember that you must replace the brake pads in time to avoid major problems.

Replace Rear Brake Pads On A Mazda 3
Great Mazda 3 Sedan

Leave a Comment