How To Change The Power Steering Pump On The Toyota RAV4

Hello! good night, at this time we will created an article about How To Change The Power Steering Pump On The Toyota RAV4

The power steering pump in your Toyota RAV4 makes it easy for drivers to steer with just one finger. Keep reading this post until the end so you can learn how to change power steering pump on toyota rav4.

When the pump is bad, you may notice a buzzing or screeching sound coming from the underside of the RAV4’s hood, especially when turning the steering wheel, or slow and increased difficulty turning the steering wheel in the course of normal driving. This sluggishness can be especially noticeable at low speeds, such as when parallel parking.

How to change the power steering pump on the Toyota RAV4

How to Remove the Power Steering Pump on the RAV4
RAV4 2001

The steps to follow to replace the power steering pump on a Toyota RAV4 are as follows:

  1. Disconnect and isolate the negative battery cable of your Toyota RAV4. Put the engine undercover, lift the hood to view the engine, and to gain access to engine operation.
  1. Loosen the locking bolt and tension bolt on the alternator until you can turn it in, releasing the tension on the drive belt. Next you need to remove the drive belt from the power steering pump pulley.
  1. Use your fingers to loosen the clamp on the suction hose and remove it from the power steering pump.. Next, use a wrench to remove the union bolt, carefully remove the gasket (being very careful not to scratch the surface under the gasket), and disconnect the pressure feed tube. Remove the connector from the oil pressure switch on the pump.
  1. Loosen the two bolts holding the pump to the vehicle. One will withdraw completely; the other will detach from the pump but will not be completely removed from the engine compartment. Remove the old power steering pump from the engine compartment.
  1. Place the new power steering pump inside the engine compartment and tighten both mounting bolts..
  1. Reconnect the oil pressure switch connector to the power steering pump, also reconnect the pressure feed tube (using a new gasket), and tighten the union bolt.
  1. Fix the suction hose again with its clamp, refit the drive belt on the power steering pump pulleyplace the alternator back in its original position and tighten the tension and locking bolts to hold it in place.
  1. Change the power steering motor. You should check the level of the power steering fluid that is housed in the reservoir under the hood and add more if necessary.
  1. Bleed the power steering system by raising the front of the RAV4 and supporting it with jack stands, then turn the steering wheel from the locked position on one side to the locked position on the other side several times. While doing this procedure the engine should be off. Then lower the vehicle to the ground, start the engine, turn the steering wheel to one side and hold for three seconds, then to the other side and hold for another three seconds.
  1. Shut off engine again, check power steering fluid levels and, again, fill it in if necessary. Repeat the process as necessary until the fluid level no longer drops and air bubbles no longer appear in the power steering fluid.

In this way you will be able to change the power steering pump of a Toyota RAV4, and solve the problems with the fluid level.

The power steering pump in your Toyota RAV4 makes it easy for drivers to steer with just one finger. Keep reading this post until the end so you can learn how to change power steering pump on toyota rav4.

When the pump is bad, you may notice a buzzing or screeching sound coming from the underside of the RAV4’s hood, especially when turning the steering wheel, or slow and increased difficulty turning the steering wheel in the course of normal driving. This sluggishness can be especially noticeable at low speeds, such as when parallel parking.

How to change the power steering pump on the Toyota RAV4

How to Remove the Power Steering Pump on the RAV4
RAV4 2001

The steps to follow to replace the power steering pump on a Toyota RAV4 are as follows:

  1. Disconnect and isolate the negative battery cable of your Toyota RAV4. Put the engine undercover, lift the hood to view the engine, and to gain access to engine operation.
  1. Loosen the locking bolt and tension bolt on the alternator until you can turn it in, releasing the tension on the drive belt. Next you need to remove the drive belt from the power steering pump pulley.
  1. Use your fingers to loosen the clamp on the suction hose and remove it from the power steering pump.. Next, use a wrench to remove the union bolt, carefully remove the gasket (being very careful not to scratch the surface under the gasket), and disconnect the pressure feed tube. Remove the connector from the oil pressure switch on the pump.
  1. Loosen the two bolts holding the pump to the vehicle. One will withdraw completely; the other will detach from the pump but will not be completely removed from the engine compartment. Remove the old power steering pump from the engine compartment.
  1. Place the new power steering pump inside the engine compartment and tighten both mounting bolts..
  1. Reconnect the oil pressure switch connector to the power steering pump, also reconnect the pressure feed tube (using a new gasket), and tighten the union bolt.
  1. Fix the suction hose again with its clamp, refit the drive belt on the power steering pump pulleyplace the alternator back in its original position and tighten the tension and locking bolts to hold it in place.
  1. Change the power steering motor. You should check the level of the power steering fluid that is housed in the reservoir under the hood and add more if necessary.
  1. Bleed the power steering system by raising the front of the RAV4 and supporting it with jack stands, then turn the steering wheel from the locked position on one side to the locked position on the other side several times. While doing this procedure the engine should be off. Then lower the vehicle to the ground, start the engine, turn the steering wheel to one side and hold for three seconds, then to the other side and hold for another three seconds.
  1. Shut off engine again, check power steering fluid levels and, again, fill it in if necessary. Repeat the process as necessary until the fluid level no longer drops and air bubbles no longer appear in the power steering fluid.

In this way you will be able to change the power steering pump of a Toyota RAV4, and solve the problems with the fluid level.

Leave a Comment