How To Change The Brakes On A Ford Windstar With Simple Steps!

Hi-ya! good night, at this time we will write an article about How To Change The Brakes On A Ford Windstar With Simple Steps!

When the surface of the brake pads are worn to such an extent that they no longer perform properly, it is inevitable to change the pads in order to perform proper braking. Read this post to the end and learn how to change the brakes on a ford windstar.

If you don’t change the pads, then the rivets on the worn pads themselves could cut grooves in the rotor area, and you’ll need to change them anyway.

How to Change the Brakes on a Ford Windstar

Replace Brakes On A Ford Windstar
Ford Windstar 1999-2000

The Ford Windstar’s anti-lock braking system is designed to stop the vehicle within standards set by the National Highway Traffic Safety Administration.

You should know that to achieve effective braking it is necessary for the brake fluid to be able to exert force towards the caliper piston against the brake pads, which in turn exert contact with the brake rotors to slow down and eventually stop. Car.

To change the brakes on a Ford Windstar follow these steps:

  1. First park the Ford vehicle in a spot that provides room to work on both sides of the vehicle and set the parking brake.
  1. Then you must loosen the nuts with the help of the iron bar or wrench.
  1. Raise the Windstar with a jack and locate the jack stands under the car’s chassis.
  1. Now you need to remove the lug nuts and remove the wheels from the car. Turn the steering to the left first to access the right brake.
  1. Then you have to remove the two bolts using the 13mm wrench. The caliper or caliper surrounds the rotor and the caliper bolts are located on the left side of the caliper that is on the right.
  1. Proceed to remove the brake line from the caliper removing the 10mm bolt at the place of the brake line to caliper attachment. Put a tray or bucket under the line to store any bits of brake fluid.
  1. Now pull the gauge from the rotor.
  1. Now pull the rotor from the Ford vehicle wheel bolts. If the rotors are fixed to the steering knuckle by rust, then you will need to use a hammer to get the rotor out of the car.
  1. Now spray the new rotor with brake cleaner and proceed to clean the remaining excess cleaner from the surfaces of the rotor and put the new rotor on the wheel axles. You must make sure that the side of the “Top-hat” of the rotor is facing outwards. The top hat is the side of the rotor that extends from the plane of the rotor and the opposite side is concave in shape.
  1. You must put the new brake pads in the new caliperIn addition, the pads must be slid to the sides of the caliper and will reflect the curve of the caliper walls.
  1. Locate the gauge around the new rotor and tighten the caliper bolts with the help of a 13mm wrench. Next you need to connect the brake line to the new caliper with a 10mm wrench.
  1. Now you must turn the steering wheel to the right and proceed to remove the caliper and rotor from the left side of the vehicle.
  1. Again put the steering wheel in neutral position; the wheels will be pointing forward.
  1. Place the wheels on the studs where they were previously, then screw on the lug nuts and remove the jack stands, also lower the car.
  1. Finally tighten the studs with the iron bar.

Tips

When changing the brakes on a Ford Windstar don’t forget:

  • Check the brake fluid level when you finish changing the Ford Windstar’s brakes. The master cylinder (which is the one that contains the fluid) is located under the hood, very close to the windshield on the driver’s side of the Ford.
  • You must press the brake pedal three to four times before starting to drive the Windstar vehicle.

Items you will need

You will need to have these things:

  • Wrench (or iron) for tires
  • Gato
  • standing cat
  • 10 millimeter wrench
  • brake cleaner spray
  • 13 millimeter wrench
  • brake pads
  • drip tray
  • Calibre
  • Rotor.

When the surface of the brake pads are worn to such an extent that they no longer perform properly, it is inevitable to change the pads in order to perform proper braking. Read this post to the end and learn how to change the brakes on a ford windstar.

If you don’t change the pads, then the rivets on the worn pads themselves could cut grooves in the rotor area, and you’ll need to change them anyway.

How to Change the Brakes on a Ford Windstar

Replace Brakes On A Ford Windstar
Ford Windstar 1999-2000

The Ford Windstar’s anti-lock braking system is designed to stop the vehicle within standards set by the National Highway Traffic Safety Administration.

You should know that to achieve effective braking it is necessary for the brake fluid to be able to exert force towards the caliper piston against the brake pads, which in turn exert contact with the brake rotors to slow down and eventually stop. Car.

To change the brakes on a Ford Windstar follow these steps:

  1. First park the Ford vehicle in a spot that provides room to work on both sides of the vehicle and set the parking brake.
  1. Then you must loosen the nuts with the help of the iron bar or wrench.
  1. Raise the Windstar with a jack and locate the jack stands under the car’s chassis.
  1. Now you need to remove the lug nuts and remove the wheels from the car. Turn the steering to the left first to access the right brake.
  1. Then you have to remove the two bolts using the 13mm wrench. The caliper or caliper surrounds the rotor and the caliper bolts are located on the left side of the caliper that is on the right.
  1. Proceed to remove the brake line from the caliper removing the 10mm bolt at the place of the brake line to caliper attachment. Put a tray or bucket under the line to store any bits of brake fluid.
  1. Now pull the gauge from the rotor.
  1. Now pull the rotor from the Ford vehicle wheel bolts. If the rotors are fixed to the steering knuckle by rust, then you will need to use a hammer to get the rotor out of the car.
  1. Now spray the new rotor with brake cleaner and proceed to clean the remaining excess cleaner from the surfaces of the rotor and put the new rotor on the wheel axles. You must make sure that the side of the “Top-hat” of the rotor is facing outwards. The top hat is the side of the rotor that extends from the plane of the rotor and the opposite side is concave in shape.
  1. You must put the new brake pads in the new caliperIn addition, the pads must be slid to the sides of the caliper and will reflect the curve of the caliper walls.
  1. Locate the gauge around the new rotor and tighten the caliper bolts with the help of a 13mm wrench. Next you need to connect the brake line to the new caliper with a 10mm wrench.
  1. Now you must turn the steering wheel to the right and proceed to remove the caliper and rotor from the left side of the vehicle.
  1. Again put the steering wheel in neutral position; the wheels will be pointing forward.
  1. Place the wheels on the studs where they were previously, then screw on the lug nuts and remove the jack stands, also lower the car.
  1. Finally tighten the studs with the iron bar.

Tips

When changing the brakes on a Ford Windstar don’t forget:

  • Check the brake fluid level when you finish changing the Ford Windstar’s brakes. The master cylinder (which is the one that contains the fluid) is located under the hood, very close to the windshield on the driver’s side of the Ford.
  • You must press the brake pedal three to four times before starting to drive the Windstar vehicle.

Items you will need

You will need to have these things:

  • Wrench (or iron) for tires
  • Gato
  • standing cat
  • 10 millimeter wrench
  • brake cleaner spray
  • 13 millimeter wrench
  • brake pads
  • drip tray
  • Calibre
  • Rotor.

Leave a Comment