How To Change The Battery Of A Ford Windstar: Step By Step!

Hello! good night, at this time we will created an article about How To Change The Battery Of A Ford Windstar: Step By Step!

A maintenance-free Ford Windstar battery needs some attention until it needs to be replaced. When the battery fails, you need to buy a replacement at an auto parts store and replace it at home in just a few minutes. Read on and learn how to change the battery in a ford windstar.

When you disconnect your vehicle’s battery, the truck’s computer is going to need reprogramming to be able to regulate the fuel mileage, in addition to the gear indicators and the prevention and warning systems. If the computer isn’t reprogrammed, you’re going to witness poor idling, decreased fuel mileage, and even engine error lights.

Steps to change the battery in a Ford Windstar

Replace The Battery In A Ford Windstar
Ford Windstar 2003

Follow these simple steps to change the battery in your Ford Windstar. Later we will explain how to reprogram the computer.

  1. You must first open the hood of your Ford Windstar.
  1. Then remove the bolts (or screws) from each end of the strap that hold the battery in the engine compartment using a wrench and ratchet. Then put the strap aside.
  1. With the help of a wrench you must loosen the connection of the negative battery cable. Then remove the battery cable and also loosen the positive battery cable and then remove it from the battery. Now clean the cable connections with a brush to remove any corrosion or dirt.
  1. You remove the battery from its original place and install the new battery where the old one was. Reconnect the positive cable and tighten the connection with the help of a wrench. Now connect the negative cable and tighten it with a wrench, you must also put the tether strap back on and tighten the bolts (or screws) with a wrench and ratchet.
  1. Finally close the hood of the car.

reprogram the computer

Replace The Battery On A Windstar
Ford Windstar color blanco

As we have mentioned in the introduction of this article, the computer of this vehicle will need a reprogramming in order to regulate the fuel mileage.

  1. First you must apply the handbrake and turn off all electrical components. Insert the key into the ignition in the car and start the van.
  1. You should let the engine idle until it reaches normal or ideal operating temperature. You have to know that the temperature will vary depending on your particular Windstar. Wait now for the temperature gauge to reach the point where it is commonly found when you are driving.
  1. Then leave the engine at operating temperature for about 60 minutes. Turn on the air conditioning and wait another 60 minutes, then you should hit the brake pedal and shift the transmission into “Drive“.
  1. Hold the brake and let the engine idle for a minute. Drive 10 miles in your Ford Windstar to complete the computer programming.

A maintenance-free Ford Windstar battery needs some attention until it needs to be replaced. When the battery fails, you need to buy a replacement at an auto parts store and replace it at home in just a few minutes. Read on and learn how to change the battery in a ford windstar.

When you disconnect your vehicle’s battery, the truck’s computer is going to need reprogramming to be able to regulate the fuel mileage, in addition to the gear indicators and the prevention and warning systems. If the computer isn’t reprogrammed, you’re going to witness poor idling, decreased fuel mileage, and even engine error lights.

Steps to change the battery in a Ford Windstar

Replace The Battery In A Ford Windstar
Ford Windstar 2003

Follow these simple steps to change the battery in your Ford Windstar. Later we will explain how to reprogram the computer.

  1. You must first open the hood of your Ford Windstar.
  1. Then remove the bolts (or screws) from each end of the strap that hold the battery in the engine compartment using a wrench and ratchet. Then put the strap aside.
  1. With the help of a wrench you must loosen the connection of the negative battery cable. Then remove the battery cable and also loosen the positive battery cable and then remove it from the battery. Now clean the cable connections with a brush to remove any corrosion or dirt.
  1. You remove the battery from its original place and install the new battery where the old one was. Reconnect the positive cable and tighten the connection with the help of a wrench. Now connect the negative cable and tighten it with a wrench, you must also put the tether strap back on and tighten the bolts (or screws) with a wrench and ratchet.
  1. Finally close the hood of the car.

reprogram the computer

Replace The Battery On A Windstar
Ford Windstar color blanco

As we have mentioned in the introduction of this article, the computer of this vehicle will need a reprogramming in order to regulate the fuel mileage.

  1. First you must apply the handbrake and turn off all electrical components. Insert the key into the ignition in the car and start the van.
  1. You should let the engine idle until it reaches normal or ideal operating temperature. You have to know that the temperature will vary depending on your particular Windstar. Wait now for the temperature gauge to reach the point where it is commonly found when you are driving.
  1. Then leave the engine at operating temperature for about 60 minutes. Turn on the air conditioning and wait another 60 minutes, then you should hit the brake pedal and shift the transmission into “Drive“.
  1. Hold the brake and let the engine idle for a minute. Drive 10 miles in your Ford Windstar to complete the computer programming.

Leave a Comment