How to Change Brake Pads on a 2007 Toyota RAV4

Hello! good afternoon, now i will write an article about How to Change Brake Pads on a 2007 Toyota RAV4

The 2007 Toyota RAV4 has front disc brakes that use disc brake pads. The compact SUV’s rear brakes can use either drum brakes or disc brakes. If the pads on your car are worn out or no longer do their job well, read on to the end and learn how to change the brake pads on a toyota rav4.

This type of SUV also has two and four-wheel drive models. While the brake pads between the two available model versions are different, the procedure for replacing them is basically the same.

The front brakes account for 70 percent of the vehicle’s stopping power, while the smaller rear pads (on rear disc brake models) only account for 30 percent.

Steps to change the brake pads on a 2007 Toyota RAV4

Replace RAV4 Brake Pads
2019 Toyota RAV4 Excel HEV CVT 2.5

The steps you must follow to change the brake pads on a Toyota RAV4 correctly are the following:

  1. Place a wheel chock behind one of the rear tires (for front brake pad replacement) or in front of one of the front tires (for rear brake pad replacement) and then siphon some of the brake fluid from the master cylinder using a brake fluid siphon. Discard the old fluid and replace the master cylinder cap.
  1. Remove the lug nuts from any axle you’re changing brake pads on. Use the lug nut wrench to loosen the lug nuts enough to separate them from the rims.
  1. Raise the appropriate axle using a jack and then support the RAV4 on the jack stand(s).. You can lift one side and complete the replacement of the brake pads if you wish, or you can lift the entire rear axle, but do not use the hydraulic jack as a support for the vehicle; they are not as reliable as fixed jack stands.
  1. Remove the lug nuts from the wheels, and then remove the tires and set them aside outside of your work area.
  1. Position the C-clamp over the caliper housing so that the top of the clamp rests against the inside of the caliper frame and the clamp’s bolt hole sits against the steel plate of the brake pad. Exterior. Slowly tighten the clamp so that the caliper piston goes all the way into its bore.
  1. Hold the upper and lower slider pins with the open end of a metric wrench, and then loosen the caliper bolts from the slider pins using the box-end side of a metric wrench.
  1. Remove the caliper from the caliper torque plate. Place the caliper in a caliper mount and secure it to the frame to prevent damage to the flex hose attached to the caliper.
  1. Remove the old brake pads, shims, brake pad spring and brake pad clips from the caliper torque plate.
  1. Install the new brake pad clips, then apply a light coating of silicone lubricant to the pad seats on the clips.. Place the replacement shims on the steel plates of the replacement pads (if they are not attached or glued), then apply or spray the shims and steel plates with an even coat of brake pad anti-squeak compound or spray. Let the compound or spray go tacky for a few minutes.
  1. Place the pads into the torsion plate pad clips, insert the pad spring, then remove the caliper from the hanger and place it over the pads and rotor.
  1. Lubricate the slide pins and insert them through the caliper. Hold the slide pins with the open end of a metric wrench and thread the caliper bolts into the pins by hand to start. After threading both bolts in by hand, use a metric wrench to tighten them.
  1. Replace the tire(s) and lug nuts, and then tighten the lug nuts snug to the tire(s). Jack up the RAV4 high enough to remove the bracket(s). Repeat pad replacement for the other side of the same axle, if you only lifted one side at a time.
  1. Use the torque wrench and a 21mm metric socket to tighten the lug nuts in a star pattern.
  1. Pump the brake pedal inside the cabin of the Rav4 SUV until it feels firm and the brake pedal is at a normal height. Check the brake fluid level in the master cylinder and, if necessary, fill it with new brake fluid to the full mark. Remove the wheel chock then test your

Well, this way you will be able to change the brake pads on a 2007 Toyota RAV4 and other models too.

Change Brake Pads On A Toyota RAV4
2001 Toyota RAV4

Items you will need

The tools or items that you will require in this job are:

  • wheel chock
  • brake fluid siphon
  • tire nut wrench
  • Cat support(s)
  • 4-inch or larger C-clamp
  • Metric Open End and Box End Combination Wrench Set
  • clamp hanger
  • Brake pad set, shims and pad clips
  • silicone brake lubricant
  • Unhygienic brake pad compound or spray
  • Torque wrench with torque wrench set
  • Brake fluid

The 2007 Toyota RAV4 has front disc brakes that use disc brake pads. The compact SUV’s rear brakes can use either drum brakes or disc brakes. If the pads on your car are worn out or no longer do their job well, read on to the end and learn how to change the brake pads on a toyota rav4.

This type of SUV also has two and four-wheel drive models. While the brake pads between the two available model versions are different, the procedure for replacing them is basically the same.

The front brakes account for 70 percent of the vehicle’s stopping power, while the smaller rear pads (on rear disc brake models) only account for 30 percent.

Steps to change the brake pads on a 2007 Toyota RAV4

Replace RAV4 Brake Pads
2019 Toyota RAV4 Excel HEV CVT 2.5

The steps you must follow to change the brake pads on a Toyota RAV4 correctly are the following:

  1. Place a wheel chock behind one of the rear tires (for front brake pad replacement) or in front of one of the front tires (for rear brake pad replacement) and then siphon some of the brake fluid from the master cylinder using a brake fluid siphon. Discard the old fluid and replace the master cylinder cap.
  1. Remove the lug nuts from any axle you’re changing brake pads on. Use the lug nut wrench to loosen the lug nuts enough to separate them from the rims.
  1. Raise the appropriate axle using a jack and then support the RAV4 on the jack stand(s).. You can lift one side and complete the replacement of the brake pads if you wish, or you can lift the entire rear axle, but do not use the hydraulic jack as a support for the vehicle; they are not as reliable as fixed jack stands.
  1. Remove the lug nuts from the wheels, and then remove the tires and set them aside outside of your work area.
  1. Position the C-clamp over the caliper housing so that the top of the clamp rests against the inside of the caliper frame and the clamp’s bolt hole sits against the steel plate of the brake pad. Exterior. Slowly tighten the clamp so that the caliper piston goes all the way into its bore.
  1. Hold the upper and lower slider pins with the open end of a metric wrench, and then loosen the caliper bolts from the slider pins using the box-end side of a metric wrench.
  1. Remove the caliper from the caliper torque plate. Place the caliper in a caliper mount and secure it to the frame to prevent damage to the flex hose attached to the caliper.
  1. Remove the old brake pads, shims, brake pad spring and brake pad clips from the caliper torque plate.
  1. Install the new brake pad clips, then apply a light coating of silicone lubricant to the pad seats on the clips.. Place the replacement shims on the steel plates of the replacement pads (if they are not attached or glued), then apply or spray the shims and steel plates with an even coat of brake pad anti-squeak compound or spray. Let the compound or spray go tacky for a few minutes.
  1. Place the pads into the torsion plate pad clips, insert the pad spring, then remove the caliper from the hanger and place it over the pads and rotor.
  1. Lubricate the slide pins and insert them through the caliper. Hold the slide pins with the open end of a metric wrench and thread the caliper bolts into the pins by hand to start. After threading both bolts in by hand, use a metric wrench to tighten them.
  1. Replace the tire(s) and lug nuts, and then tighten the lug nuts snug to the tire(s). Jack up the RAV4 high enough to remove the bracket(s). Repeat pad replacement for the other side of the same axle, if you only lifted one side at a time.
  1. Use the torque wrench and a 21mm metric socket to tighten the lug nuts in a star pattern.
  1. Pump the brake pedal inside the cabin of the Rav4 SUV until it feels firm and the brake pedal is at a normal height. Check the brake fluid level in the master cylinder and, if necessary, fill it with new brake fluid to the full mark. Remove the wheel chock then test your

Well, this way you will be able to change the brake pads on a 2007 Toyota RAV4 and other models too.

Change Brake Pads On A Toyota RAV4
2001 Toyota RAV4

Items you will need

The tools or items that you will require in this job are:

  • wheel chock
  • brake fluid siphon
  • tire nut wrench
  • Cat support(s)
  • 4-inch or larger C-clamp
  • Metric Open End and Box End Combination Wrench Set
  • clamp hanger
  • Brake pad set, shims and pad clips
  • silicone brake lubricant
  • Unhygienic brake pad compound or spray
  • Torque wrench with torque wrench set
  • Brake fluid

Leave a Comment