How to Change a Water Pump on a Chevrolet Aveo

Hi-ya! good night, now i will made an article about How to Change a Water Pump on a Chevrolet Aveo

The water pump on a 1.61 Chevrolet Aveo pushes coolant from the radiator and through the engine block, ensuring coolant is always circulating through the system. If your car’s water pump fails, then the coolant sits in the engine block, heating up because it doesn’t get a chance to cool down. Read this post to the end and learn how to change the water pump on a Chevrolet Aveo.

If the coolant settles it will cause the engine to overheat which could cause extensive damage. If your Aveo’s water pump fails, replace it with a new one, it may take as long as three hours to do so.

How to Change a Water Pump on a Chevrolet Aveo

How to Remove a Water Pump on a Chevy Aveo
Chevy Aveo LT Sedan

It’s good to change your Aveo’s water pump when it begins to fail. The steps you must follow to replace the water pump in a Chevrolet Aveo are as follows:

  1. Let your Chevy Aveo cool down for at least four hours. Place the drain pan under the radiator and open the radiator drain plug by hand. Empty the radiator into a drain pan.
  1. Remove the hose clamps that hold the radiator hoses to the water pump on the passenger side of the engine with a flathead screwdriver. Remove the radiator hoses from the water pump.
  1. Unbolt the rearmost timing belt cover on the engine with the ratchet and 3/8-inch wrench. Unscrew the water pump from the engine block using the 3/8-inch socket and ratchet. Then pull it out of the block and scrape the engine mounting surface with the gasket scraper to clean any remaining gasket residue.
  1. Apply gasket sealant to engine mounting surface. Mount the replacement water pump with the replacement gasket to the engine using the 3/8-inch wrench and wrench set.
  1. Reinstall the lower timing belt cover with the ratchet and 3/8-inch wrench. Then reinstall the radiator hoses on the water pump with the flathead screwdriver.
  1. open the radiator cap. Fill the radiator with the 50-50 pre-diluted coolant and start the car, plus turn the heater on high. Let the Aveo run for 10 minutes, then turn off the car, open the radiator cap again, and add as much coolant as needed to fill the system.

Advice

Changing a water pump on a Chevrolet Aveo is a process that anyone can do at home, you just need to have the right tools and follow the correct steps.

Items you will need

The items you will use in this repair are the following:

  • flat head screwdriver
  • Wrench Set (Ratchet) and 3/8-inch wrench
  • replacement water pump
  • replacement water pump gasket
  • Pre-diluted coolant 50-50

The water pump on a 1.61 Chevrolet Aveo pushes coolant from the radiator and through the engine block, ensuring coolant is always circulating through the system. If your car’s water pump fails, then the coolant sits in the engine block, heating up because it doesn’t get a chance to cool down. Read this post to the end and learn how to change the water pump on a Chevrolet Aveo.

If the coolant settles it will cause the engine to overheat which could cause extensive damage. If your Aveo’s water pump fails, replace it with a new one, it may take as long as three hours to do so.

How to Change a Water Pump on a Chevrolet Aveo

How to Remove a Water Pump on a Chevy Aveo
Chevy Aveo LT Sedan

It’s good to change your Aveo’s water pump when it begins to fail. The steps you must follow to replace the water pump in a Chevrolet Aveo are as follows:

  1. Let your Chevy Aveo cool down for at least four hours. Place the drain pan under the radiator and open the radiator drain plug by hand. Empty the radiator into a drain pan.
  1. Remove the hose clamps that hold the radiator hoses to the water pump on the passenger side of the engine with a flathead screwdriver. Remove the radiator hoses from the water pump.
  1. Unbolt the rearmost timing belt cover on the engine with the ratchet and 3/8-inch wrench. Unscrew the water pump from the engine block using the 3/8-inch socket and ratchet. Then pull it out of the block and scrape the engine mounting surface with the gasket scraper to clean any remaining gasket residue.
  1. Apply gasket sealant to engine mounting surface. Mount the replacement water pump with the replacement gasket to the engine using the 3/8-inch wrench and wrench set.
  1. Reinstall the lower timing belt cover with the ratchet and 3/8-inch wrench. Then reinstall the radiator hoses on the water pump with the flathead screwdriver.
  1. open the radiator cap. Fill the radiator with the 50-50 pre-diluted coolant and start the car, plus turn the heater on high. Let the Aveo run for 10 minutes, then turn off the car, open the radiator cap again, and add as much coolant as needed to fill the system.

Advice

Changing a water pump on a Chevrolet Aveo is a process that anyone can do at home, you just need to have the right tools and follow the correct steps.

Items you will need

The items you will use in this repair are the following:

  • flat head screwdriver
  • Wrench Set (Ratchet) and 3/8-inch wrench
  • replacement water pump
  • replacement water pump gasket
  • Pre-diluted coolant 50-50

Leave a Comment