How To Change A Tire On A Chevrolet Tahoe Correctly!

Hello! good night, at this time we will write an article about How To Change A Tire On A Chevrolet Tahoe Correctly!

A flat or damaged tire on a Chevy Tahoe should be removed and changed immediately. This time you will learn how to change a tire on the Chevrolet Tahoe. The Tahoe is a heavy SUV and driving with a flat or soft tire can result in injury to the driver and passengers.

Steps to Change a Tire on a Chevrolet Tahoe

Although the Tahoe’s tires are heavy (about 45 pounds) and large, it’s not difficult to change a tire on this car. Continue reading and follow the steps that we show you:

Jack and spare wheel kit

Read your owner’s manual to locate the connection kit. The Tahoe cat kit will be in a compartment in the rear of the vehicle. Locate the access hole for the spare tire hoist. Most of the access holes are in the rear bumper.

  1. If the spare tire or wheel is mounted on the back of the vehicle’s tailgate, remove it and go to the tire replacement section.
  1. Insert the open end of the jack extension handle from the jack kit into the hoist’s access hole until it engages with the hoist’s shaft. Turn the extension handle counterclockwise to lower the spare tire to the ground.
  1. Pull up on the retaining clip in the center of the spare tire to remove it from the hoist cable.
  1. Turn the extension handle clockwise to wind the hoist cable onto the vehicle.

tire replacement

Make sure the vehicle is in gear first, or in “park” if the transmission is automatic. Put on the emergency brake.

  1. Use the flat end of the lug wrench to remove the center lug nut cap or hub cap.
  1. Place the socket end of the socket wrench in a locknut and turn it counterclockwise to loosen the locknut one or two turns. Loosen the remaining nuts, but do not remove them.
  1. Place the jack under the vehicle frame. If you’re changing a front tire, the jacking point is behind the wheel well, where the rack overlaps. In the case of a rear tire, the lifting point is located directly behind the wheel well. If you can’t locate the lift points, please refer to the user manual.
  1. Use the jack and extension handles to raise the vehicle until the wheel is at least 2 inches off the ground.
  1. Use the wrench to completely remove the nuts. Put the studs in a safe place.
  1. Remove the damaged tire and roll it to the side.
  1. Place the spare tire on the wheel studs. Push the tire against the wheel hub and screw the lug nuts onto the wheel studs by hand. Do not cross thread the lug nuts. They should turn easily.
  1. Use the jack to slowly lower the vehicle to the ground.
  1. use the wrench to tighten the nuts in a criss-cross order until all the nuts are tight.
  1. Return the jack kit to the vehicle and put the damaged tire in the rear of the vehicle. There is a possibility that the tire can be repairedthat is if the damage is located in the tread area.

Advice

If the lug nuts don’t loosen to remove the Tahoe’s tire, use your foot to push down or stand on the tire wrench. You can also use your foot to tighten the studs.

warnings

Make sure the Chevrolet Tahoe is parked on a level surface when you go to change the tire if you are parked on the side of the road, turn on your four-way hazard flashers.

Don’t drag yourself under the vehicle while it’s jacked up. A tire jack is not meant to be a foot jack.

Remove a tire or wheel on a Chevy Tahoe
Chevrolet Tahoe LT 2009

A flat or damaged tire on a Chevy Tahoe should be removed and changed immediately. This time you will learn how to change a tire on the Chevrolet Tahoe. The Tahoe is a heavy SUV and driving with a flat or soft tire can result in injury to the driver and passengers.

Steps to Change a Tire on a Chevrolet Tahoe

Although the Tahoe’s tires are heavy (about 45 pounds) and large, it’s not difficult to change a tire on this car. Continue reading and follow the steps that we show you:

Jack and spare wheel kit

Read your owner’s manual to locate the connection kit. The Tahoe cat kit will be in a compartment in the rear of the vehicle. Locate the access hole for the spare tire hoist. Most of the access holes are in the rear bumper.

  1. If the spare tire or wheel is mounted on the back of the vehicle’s tailgate, remove it and go to the tire replacement section.
  1. Insert the open end of the jack extension handle from the jack kit into the hoist’s access hole until it engages with the hoist’s shaft. Turn the extension handle counterclockwise to lower the spare tire to the ground.
  1. Pull up on the retaining clip in the center of the spare tire to remove it from the hoist cable.
  1. Turn the extension handle clockwise to wind the hoist cable onto the vehicle.

tire replacement

Make sure the vehicle is in gear first, or in “park” if the transmission is automatic. Put on the emergency brake.

  1. Use the flat end of the lug wrench to remove the center lug nut cap or hub cap.
  1. Place the socket end of the socket wrench in a locknut and turn it counterclockwise to loosen the locknut one or two turns. Loosen the remaining nuts, but do not remove them.
  1. Place the jack under the vehicle frame. If you’re changing a front tire, the jacking point is behind the wheel well, where the rack overlaps. In the case of a rear tire, the lifting point is located directly behind the wheel well. If you can’t locate the lift points, please refer to the user manual.
  1. Use the jack and extension handles to raise the vehicle until the wheel is at least 2 inches off the ground.
  1. Use the wrench to completely remove the nuts. Put the studs in a safe place.
  1. Remove the damaged tire and roll it to the side.
  1. Place the spare tire on the wheel studs. Push the tire against the wheel hub and screw the lug nuts onto the wheel studs by hand. Do not cross thread the lug nuts. They should turn easily.
  1. Use the jack to slowly lower the vehicle to the ground.
  1. use the wrench to tighten the nuts in a criss-cross order until all the nuts are tight.
  1. Return the jack kit to the vehicle and put the damaged tire in the rear of the vehicle. There is a possibility that the tire can be repairedthat is if the damage is located in the tread area.

Advice

If the lug nuts don’t loosen to remove the Tahoe’s tire, use your foot to push down or stand on the tire wrench. You can also use your foot to tighten the studs.

warnings

Make sure the Chevrolet Tahoe is parked on a level surface when you go to change the tire if you are parked on the side of the road, turn on your four-way hazard flashers.

Don’t drag yourself under the vehicle while it’s jacked up. A tire jack is not meant to be a foot jack.

Remove a tire or wheel on a Chevy Tahoe
Chevrolet Tahoe LT 2009

Leave a Comment