How To Change A Car Radio Fuse? – Steps And Tips!

Hi! good morning, at this moment we will created an article about How To Change A Car Radio Fuse? – Steps And Tips!

Your vehicle’s electrical system is complex, consisting of miles of electrical wiring. Thanks to the manufacturer’s commitment to providing you with a perfectly functioning and secure cabling system, such a network is rarely thought of. The vehicle’s fuse box, which protects the electrical system from electrical overloads and short circuits. If there is a blackout in your radio you may need to change radio fuse.

How to change the radio fuse

The steps to replace your car radio fuse are as follows:

  1. Park the vehicle and apply the parking brake.
  1. Identify the fuse panel. This is typically on the driver’s side of the dash. It can also be placed under the dash or under the hood of the vehicle in the engine compartment. Check your vehicle owner’s manual to determine where the fuse holder is located.
  1. Check the fuse diagram. To locate the radio fuse you should consult the owner’s manual or the diagram on the back of the fuse block cover. There will usually be a drawing of the fuse block that identifies the fuses by function and amperage (15, 20, 25 or 30 amp fuses).
  1. remove the fuse. Use the fuse puller (or pliers) to grab the fuse you suspect is blown, in this case the radio fuse, and pull it out of the fuse block. If you don’t have a fuse puller, you can substitute a pair of pliers or needle nose pliers or just use your fingers. check the fuse. If the small metal bar in the center of the fuse is burned out, you should replace it with a similar fuse of the same rating (color).
  1. change the fuse. Put a new fuse of the same color and amperage rating in the slot of the blown radio fuse you removed. Turn the key to the accessory position and turn on your radio to verify that the problem has been resolved.
  1. Replace the fuse holder cover, turn off the radio, and turn the key to the “Off” position.

Advice

It’s a good idea to familiarize yourself with the location of your fuse box in daylight before you need it. This will save you time when you need to access it in the dark.

Caveat

Never replace a blown fuse with a higher capacity fuse.this may cause a wiring fire.

Your vehicle’s electrical system is complex, consisting of miles of electrical wiring. Thanks to the manufacturer’s commitment to providing you with a perfectly functioning and secure cabling system, such a network is rarely thought of. The vehicle’s fuse box, which protects the electrical system from electrical overloads and short circuits. If there is a blackout in your radio you may need to change radio fuse.

How to change the radio fuse

The steps to replace your car radio fuse are as follows:

  1. Park the vehicle and apply the parking brake.
  1. Identify the fuse panel. This is typically on the driver’s side of the dash. It can also be placed under the dash or under the hood of the vehicle in the engine compartment. Check your vehicle owner’s manual to determine where the fuse holder is located.
  1. Check the fuse diagram. To locate the radio fuse you should consult the owner’s manual or the diagram on the back of the fuse block cover. There will usually be a drawing of the fuse block that identifies the fuses by function and amperage (15, 20, 25 or 30 amp fuses).
  1. remove the fuse. Use the fuse puller (or pliers) to grab the fuse you suspect is blown, in this case the radio fuse, and pull it out of the fuse block. If you don’t have a fuse puller, you can substitute a pair of pliers or needle nose pliers or just use your fingers. check the fuse. If the small metal bar in the center of the fuse is burned out, you should replace it with a similar fuse of the same rating (color).
  1. change the fuse. Put a new fuse of the same color and amperage rating in the slot of the blown radio fuse you removed. Turn the key to the accessory position and turn on your radio to verify that the problem has been resolved.
  1. Replace the fuse holder cover, turn off the radio, and turn the key to the “Off” position.

Advice

It’s a good idea to familiarize yourself with the location of your fuse box in daylight before you need it. This will save you time when you need to access it in the dark.

Caveat

Never replace a blown fuse with a higher capacity fuse.this may cause a wiring fire.

Leave a Comment