Hi! good morning, at this moment i will write an article about Brake Light Problems In A Kia Sportage And Solutions!
Los brake light problems on a kia sportage they don’t have to be a puzzle. There are certain faults that show up over and over again when diagnosing brake light problems, which makes it much easier to find out what happens to the brakes when you hit the pedal.
Take a look at these four common brake light problems and how you can solve them. We’ll also tell you how to change a brake light bulb on a KIA Sportage.
Brake Light Problems on a Kia Sportage
If you keep in mind what you will read here, most brake light problems on your kia Sportage will be easy to diagnose and fix on your own.
1. Bulb burnt out
A burned out bulb is by far one of the most common brake light problems on a Kia Sportage, and it’s easy to see why. Think about the time you spend with your foot on the brake, and then consider that the bulb has to be lit for that entire period.
Newer models have switched to LED lights that last much longer, but older vehicles still have bulbs that need to be pulled out and replaced. It’s cheap and easy to do, most of the time, with a basic set of tools.
2. Faulty brake light switch
When the brake pedal is depressed, a switch is activated that sends a signal to the taillights that it’s time to come on. Analog switches wear out over time, and can also get dirty, which interferes with their ability to make positive contact and transmit the correct signal.
Replacing the switch isn’t a big job, and it’s also easy for your mechanic to check for brake light problems like this. If all three brake lights go out at the same time, it’s unlikely that the trio of bulbs died simultaneously. In this case, it is more likely that the brake light switch is bad.
3. Blown fuse
If the lights on your kia Sportage do not illuminate on either side and the brake light switch is OK, then the next thing to check is the brake light fuse. Locate your vehicle’s fuse box, which is usually under the hood or in the cockpit control panel.
You must make use of the fuse diagram found on the cover of the box (or in the manual), look for the brake circuit fuse and make sure it has not blown. If it has, you should replace it with a fuse of the same resistance.
4. Defective plug
If you have only one brake light out on your kia Sportage and the bulb is OK, the next step is to check the light socket itself. Brake light problems can include a socket whose connections are dirty or corrodedor one whose wiring has worn down to the point that it only makes an intermittent connection.
Changing an outlet is as simple as cutting the old wires and splicing in the new unit, which is usually a cheap part to buy.
How to change a brake light bulb on a KIA Sportage?
Perhaps one of the bulbs that go from being perceived in any vehicle is the brake lights. Turn signals may come on quickly when turning on the turn signal, indicating a bulb has gone out in the front or rear, although most vehicles do not provide a warning signal when the brake light goes out .
Also, you can’t press down on the brake pedal and see if the brake lights respond to your input. You can ask a person to help and see if the lights are activated or not.
Replacing a brake light bulb on a Sportage is a no-brainer and can still save you some cash on hand. The steps are the following:
- Put a helper in your Kia Sportage and have him go through all the lights while he’s in it.
- Open the back door.
- Using the brake light assembly as a guide, you should look at the metal door rail on the side. You will notice two seated screws, which should be removed with the help of a Phillips screwdriver.
- Next, stand on the outside of the brake light assembly and gently but firmly pull on it. The lens is not released by the two screws, but is still held in place by a ball socket on the inside of the trim.
- You must turn the zone lamp socket on the back of the lens assembly in a counterclockwise direction to get it loose. You must remove the cap and remove the bulb by also turning half a turn to the left while gently pushing on it.
- Now you must insert the new bulb, turning it half a turn to the right and slightly pushing it in.
- Have your assistant hit the brakes again and thereby test the new bulb.
- Reinsert the plug into the lens assembly, and then turn it clockwise a half turn.
- Align the ball joint and fit the assembly in its respective place.
- Again reinsert the screws you had removed and close the door.
things you will need
The items and things you will need to change a brake light bulb on a KIA Sportage are as follows:
Los brake light problems on a kia sportage they don’t have to be a puzzle. There are certain faults that show up over and over again when diagnosing brake light problems, which makes it much easier to find out what happens to the brakes when you hit the pedal.
Take a look at these four common brake light problems and how you can solve them. We’ll also tell you how to change a brake light bulb on a KIA Sportage.
Brake Light Problems on a Kia Sportage
If you keep in mind what you will read here, most brake light problems on your kia Sportage will be easy to diagnose and fix on your own.
1. Bulb burnt out
A burned out bulb is by far one of the most common brake light problems on a Kia Sportage, and it’s easy to see why. Think about the time you spend with your foot on the brake, and then consider that the bulb has to be lit for that entire period.
Newer models have switched to LED lights that last much longer, but older vehicles still have bulbs that need to be pulled out and replaced. It’s cheap and easy to do, most of the time, with a basic set of tools.
2. Faulty brake light switch
When the brake pedal is depressed, a switch is activated that sends a signal to the taillights that it’s time to come on. Analog switches wear out over time, and can also get dirty, which interferes with their ability to make positive contact and transmit the correct signal.
Replacing the switch isn’t a big job, and it’s also easy for your mechanic to check for brake light problems like this. If all three brake lights go out at the same time, it’s unlikely that the trio of bulbs died simultaneously. In this case, it is more likely that the brake light switch is bad.
3. Blown fuse
If the lights on your kia Sportage do not illuminate on either side and the brake light switch is OK, then the next thing to check is the brake light fuse. Locate your vehicle’s fuse box, which is usually under the hood or in the cockpit control panel.
You must make use of the fuse diagram found on the cover of the box (or in the manual), look for the brake circuit fuse and make sure it has not blown. If it has, you should replace it with a fuse of the same resistance.
4. Defective plug
If you have only one brake light out on your kia Sportage and the bulb is OK, the next step is to check the light socket itself. Brake light problems can include a socket whose connections are dirty or corrodedor one whose wiring has worn down to the point that it only makes an intermittent connection.
Changing an outlet is as simple as cutting the old wires and splicing in the new unit, which is usually a cheap part to buy.
How to change a brake light bulb on a KIA Sportage?
Perhaps one of the bulbs that go from being perceived in any vehicle is the brake lights. Turn signals may come on quickly when turning on the turn signal, indicating a bulb has gone out in the front or rear, although most vehicles do not provide a warning signal when the brake light goes out .
Also, you can’t press down on the brake pedal and see if the brake lights respond to your input. You can ask a person to help and see if the lights are activated or not.
Replacing a brake light bulb on a Sportage is a no-brainer and can still save you some cash on hand. The steps are the following:
- Put a helper in your Kia Sportage and have him go through all the lights while he’s in it.
- Open the back door.
- Using the brake light assembly as a guide, you should look at the metal door rail on the side. You will notice two seated screws, which should be removed with the help of a Phillips screwdriver.
- Next, stand on the outside of the brake light assembly and gently but firmly pull on it. The lens is not released by the two screws, but is still held in place by a ball socket on the inside of the trim.
- You must turn the zone lamp socket on the back of the lens assembly in a counterclockwise direction to get it loose. You must remove the cap and remove the bulb by also turning half a turn to the left while gently pushing on it.
- Now you must insert the new bulb, turning it half a turn to the right and slightly pushing it in.
- Have your assistant hit the brakes again and thereby test the new bulb.
- Reinsert the plug into the lens assembly, and then turn it clockwise a half turn.
- Align the ball joint and fit the assembly in its respective place.
- Again reinsert the screws you had removed and close the door.
things you will need
The items and things you will need to change a brake light bulb on a KIA Sportage are as follows:
