9 Simple Steps To Change The Oil In A Hyundai Tucson

Hi! good night, this day we will write an article about 9 Simple Steps To Change The Oil In A Hyundai Tucson

The oil in a Hyundai Tucson vehicle acts as a lubricant for the internal mechanisms of the engine to prevent them from becoming oppressed, and the manufacturer of this car recommends an oil change every 3,000 or 5,000 miles, depending on driving conditions. Read on and learn how to change the oil in a hyundai tucson correctly.

A limit of 10,000 miles or more between oil changes is not tolerable at all, since the oil becomes cloudy over time due to the heat built up inside the engine. While the oil favors the maintenance of adequate friction of the internal mechanisms, and with it and the great heat, changing the oil is necessary to protect the engine.

How to Change the Oil in a Hyundai Tucson

The heat in the engine ends up degrading the oil little by little, and for good engine health we must change it. The steps required to change the oil in a Tucson are as follows:

  1. First you must raise the front segment of the vehicle with a shackle or cricket, you have to place it under the axis of the wheels and proceed to raise the car.
  1. Place a fixed tower on each of the front and rear axles so they can support the raised car.
  1. Go under the car and put the oil collection plate, it should be just under the oil valve.
  1. Now proceed to remove the oil valve plug so that it can be drained.
  1. Remove the oil filterit is located directly on the oil valve and is screwed into the engine housing, then you must turn the filter making movements to the left to remove it.
  1. Replace the plug in its respective place once all the oil has been drained.
  1. You should put a small amount of new oil on the rubber seal of the new oil filter, and then put the new oil filter on and press to tighten only using your hand.
  1. Open the oil valve cap and put in 4 liters of new oil, then to test the oil level, grab the dipstick and clean it real good, then reinsert and remove. The oil level should be between the upper and lower marks on the dipstick., if it is not this way, you are going to have to add more oil until finally the level is located between the marks. Then you must press the valve cap when you have finished and that’s it.
  1. Remove the oil pan from the bottom of the vehicle and lower the car to the ground.

Tips

To change the oil in a Hyundai Tucson correctly and without causing any type of damage, you must follow these steps to the letter.

Drain The Oil In A Hyundai Tucson
Hyundai Tucson 2.0 CRDi 2017

The oil in a Hyundai Tucson vehicle acts as a lubricant for the internal mechanisms of the engine to prevent them from becoming oppressed, and the manufacturer of this car recommends an oil change every 3,000 or 5,000 miles, depending on driving conditions. Read on and learn how to change the oil in a hyundai tucson correctly.

A limit of 10,000 miles or more between oil changes is not tolerable at all, since the oil becomes cloudy over time due to the heat built up inside the engine. While the oil favors the maintenance of adequate friction of the internal mechanisms, and with it and the great heat, changing the oil is necessary to protect the engine.

How to Change the Oil in a Hyundai Tucson

The heat in the engine ends up degrading the oil little by little, and for good engine health we must change it. The steps required to change the oil in a Tucson are as follows:

  1. First you must raise the front segment of the vehicle with a shackle or cricket, you have to place it under the axis of the wheels and proceed to raise the car.
  1. Place a fixed tower on each of the front and rear axles so they can support the raised car.
  1. Go under the car and put the oil collection plate, it should be just under the oil valve.
  1. Now proceed to remove the oil valve plug so that it can be drained.
  1. Remove the oil filterit is located directly on the oil valve and is screwed into the engine housing, then you must turn the filter making movements to the left to remove it.
  1. Replace the plug in its respective place once all the oil has been drained.
  1. You should put a small amount of new oil on the rubber seal of the new oil filter, and then put the new oil filter on and press to tighten only using your hand.
  1. Open the oil valve cap and put in 4 liters of new oil, then to test the oil level, grab the dipstick and clean it real good, then reinsert and remove. The oil level should be between the upper and lower marks on the dipstick., if it is not this way, you are going to have to add more oil until finally the level is located between the marks. Then you must press the valve cap when you have finished and that’s it.
  1. Remove the oil pan from the bottom of the vehicle and lower the car to the ground.

Tips

To change the oil in a Hyundai Tucson correctly and without causing any type of damage, you must follow these steps to the letter.

Drain The Oil In A Hyundai Tucson
Hyundai Tucson 2.0 CRDi 2017

Leave a Comment