8 Steps to Change Brake Pads on a Silverado

Hi-ya! good morning, this day i will made an article about 8 Steps to Change Brake Pads on a Silverado

Chevrolet Silverado four-wheel disc brakes should be serviced regularly: it is recommended that you change the brake pads every 50,000 miles. Worn brake pads can severely compromise a car’s stopping power and lead to brake disc damage. Read on and learn how to change brake pads on a silverado.

The braking system depends on its elements working in concert to slow down and stop the truck on braking. Periodically check the brake pads, brake lines, discs, and brake fluid level in the truck’s master cylinder.

How to change the brake pads on a Silverado?

Remove Brake Pads On A Chevy Silverado
Chevrolet Silverado 2019

The brake pads on a Chevrolet Silverado are the most disturbed by the abuse delivered to the brake system when the vehicle is stopped. The pads are pressed against the brake rotors to bring the truck to a stop, though each time this happens, a tiny amount of pad material is worn off the surface of the rotor.

Well sooner or later but, at some point you are going to have to replace the brake pads on your Chevy Silverado. Anyone with minimal self-repair experience can do this task in just a for hours. Here are the steps to follow:

  1. Park the truck on a relatively flat surface.. Place the 2 chocks on the wheels you won’t be working on.
  1. Turn all the lug nuts on the truck’s front studs counterclockwise to make them give.
  1. Raise the front end off the ground and place the jack under the front frame; then lower the Silverado onto the climbing shoes, carefully. Manually remove the lug nuts and front wheels.
  1. Place a drop pan under the Silverado’s left front brake assembly. Rinse all brake dust off the rotor, caliper, and hub with brake cleaner.
  1. Unbolt the Silverado’s left front brake caliper using the socket set. Lift the caliper out of the caliper bracket and remove old brake pads manually.
  1. Thoroughly wash the inside of the Silverado’s left front caliper with brake cleaner to remove brake dust. Lubricate the slide pins with white lithium grease. Push the pistons back into the caliper with the caliper tool.
  1. Put the new brake pads on the Chevy Silverado in their respective position manually. Slide the caliper back over the brake rotor and thread the caliper bolts in by hand. Tighten the bolts with the socket wrench set.
  1. Move to the right front of the Silverado and repeat steps three through seven. Attach the front wheels and lug nuts to the truck by hand. Lower the Silverado off the jack’s feet using the floor jack.
  1. Torque the Silverado’s front lug nuts to 140 foot-pounds using the torque wrench. Move the wheel chocks away from the truck’s rear tire before driving.

With these steps changing the brake pads on a Silverado is a very easy task,

Tips

You should know that:

  • Change the brake pads when you hear the wear indicators rubbing against the rotors or when the brake pedal response is softer than normal.
  • To brake the new front brake pads, you just need to drive normally for the first few hundred miles, trying to avoid any hard or “panic” stops, which can cause the new pads to fade and be noisy and/or not they work so well.
  • It’s also a good idea to regularly check for brake fluid droplets that could indicate a leak, check the brake fluid level in the reservoir, and also check that the lug nuts are still tight.

Items you will need

The tools and items to use are:

  • Socket set (or socket)
  • caliper piston tool

Chevrolet Silverado four-wheel disc brakes should be serviced regularly: it is recommended that you change the brake pads every 50,000 miles. Worn brake pads can severely compromise a car’s stopping power and lead to brake disc damage. Read on and learn how to change brake pads on a silverado.

The braking system depends on its elements working in concert to slow down and stop the truck on braking. Periodically check the brake pads, brake lines, discs, and brake fluid level in the truck’s master cylinder.

How to change the brake pads on a Silverado?

Remove Brake Pads On A Chevy Silverado
Chevrolet Silverado 2019

The brake pads on a Chevrolet Silverado are the most disturbed by the abuse delivered to the brake system when the vehicle is stopped. The pads are pressed against the brake rotors to bring the truck to a stop, though each time this happens, a tiny amount of pad material is worn off the surface of the rotor.

Well sooner or later but, at some point you are going to have to replace the brake pads on your Chevy Silverado. Anyone with minimal self-repair experience can do this task in just a for hours. Here are the steps to follow:

  1. Park the truck on a relatively flat surface.. Place the 2 chocks on the wheels you won’t be working on.
  1. Turn all the lug nuts on the truck’s front studs counterclockwise to make them give.
  1. Raise the front end off the ground and place the jack under the front frame; then lower the Silverado onto the climbing shoes, carefully. Manually remove the lug nuts and front wheels.
  1. Place a drop pan under the Silverado’s left front brake assembly. Rinse all brake dust off the rotor, caliper, and hub with brake cleaner.
  1. Unbolt the Silverado’s left front brake caliper using the socket set. Lift the caliper out of the caliper bracket and remove old brake pads manually.
  1. Thoroughly wash the inside of the Silverado’s left front caliper with brake cleaner to remove brake dust. Lubricate the slide pins with white lithium grease. Push the pistons back into the caliper with the caliper tool.
  1. Put the new brake pads on the Chevy Silverado in their respective position manually. Slide the caliper back over the brake rotor and thread the caliper bolts in by hand. Tighten the bolts with the socket wrench set.
  1. Move to the right front of the Silverado and repeat steps three through seven. Attach the front wheels and lug nuts to the truck by hand. Lower the Silverado off the jack’s feet using the floor jack.
  1. Torque the Silverado’s front lug nuts to 140 foot-pounds using the torque wrench. Move the wheel chocks away from the truck’s rear tire before driving.

With these steps changing the brake pads on a Silverado is a very easy task,

Tips

You should know that:

  • Change the brake pads when you hear the wear indicators rubbing against the rotors or when the brake pedal response is softer than normal.
  • To brake the new front brake pads, you just need to drive normally for the first few hundred miles, trying to avoid any hard or “panic” stops, which can cause the new pads to fade and be noisy and/or not they work so well.
  • It’s also a good idea to regularly check for brake fluid droplets that could indicate a leak, check the brake fluid level in the reservoir, and also check that the lug nuts are still tight.

Items you will need

The tools and items to use are:

  • Socket set (or socket)
  • caliper piston tool

Leave a Comment