5 Steps To Change The Thermostat In A Nissan Rogue

Hi-ya! good afternoon, today we will created an article about 5 Steps To Change The Thermostat In A Nissan Rogue

If your Nissan Rogue is running hot, or perhaps the temperature gauge isn’t reading the temperature at all, then it’s time to change the thermostat on your nissan rogue. You won’t need any special tools to change a thermostat on a Nissan Rogue vehicle, just a few common tools you may already have around the house.

Go to your local auto parts store and order your correct replacement thermostat for the year and for your Nissan Rogue, and once you have it, just an hour or two is going to be enough to replace your Rogue’s thermostat and get back to streets.

How to change the thermostat on a Nissan Rogue:

The steps to replace the thermostat on your Nissan Rogue vehicle are as follows:

  1. Park your vehicle on a surface that is completely level. With the engine cold, place a bucket or bucket under the radiator drain valve (located on the driver’s side of the radiator), then open the drain. You should let the radiator drain for about 10 minutes (it is not necessary to drain all of the liquid it contains).
  1. Follow the upper hose of your radiator to where it connects to the engine unit.. The hose is connected to the thermostat housing, then you must use a flat head screwdriver to release the hose clamp and proceed to remove the hose from the thermostat housing.
  1. Remove the two screws that are holding the thermostat housing in place. Using a socket wrench, remove the bolts as well, and then pull out the casing. Remove the old gasket, you may need to use a paint scraper to get all of the old gasket off the housing surface.
  1. Now you must squeeze the raised area of ​​the thermostat with your thumb and forefinger and pull the thermostat from your seat, and then change the thermostat by inserting the new one in the same way that you removed the old one, but following the steps in reverse and making sure that the thermostat spring coil is inside the seat.
  1. Put the new gasket on the housing, put the thermostat housing back to its original position and again put the screws and also the hose, finally close the radiator drain cock and fill the coolant.

Advice

When you go to change the thermostat on a Nissan Rogue you should remove the air filter for easier access to the thermostat housing.

Caveat

Never disconnect any part of the car’s cooling system while the engine is hot.. The coolant inside your Rogue vehicle is going to be under pressure and can seriously injure or burn you if it is released from the system.

Items you will need

The articles or tools that you are going to use to carry out this substitution are the following:

  • Tray
  • Screwdriver
  • socket wrench set
  • paint scraper
  • Coolant
How to change the thermostat on a Nissan Rogue:
Nissan Rogue S AWD

Also find out about: The Steps To Programming The Remote Key Fob On A Nissan Rogue

If your Nissan Rogue is running hot, or perhaps the temperature gauge isn’t reading the temperature at all, then it’s time to change the thermostat on your nissan rogue. You won’t need any special tools to change a thermostat on a Nissan Rogue vehicle, just a few common tools you may already have around the house.

Go to your local auto parts store and order your correct replacement thermostat for the year and for your Nissan Rogue, and once you have it, just an hour or two is going to be enough to replace your Rogue’s thermostat and get back to streets.

How to change the thermostat on a Nissan Rogue:

The steps to replace the thermostat on your Nissan Rogue vehicle are as follows:

  1. Park your vehicle on a surface that is completely level. With the engine cold, place a bucket or bucket under the radiator drain valve (located on the driver’s side of the radiator), then open the drain. You should let the radiator drain for about 10 minutes (it is not necessary to drain all of the liquid it contains).
  1. Follow the upper hose of your radiator to where it connects to the engine unit.. The hose is connected to the thermostat housing, then you must use a flat head screwdriver to release the hose clamp and proceed to remove the hose from the thermostat housing.
  1. Remove the two screws that are holding the thermostat housing in place. Using a socket wrench, remove the bolts as well, and then pull out the casing. Remove the old gasket, you may need to use a paint scraper to get all of the old gasket off the housing surface.
  1. Now you must squeeze the raised area of ​​the thermostat with your thumb and forefinger and pull the thermostat from your seat, and then change the thermostat by inserting the new one in the same way that you removed the old one, but following the steps in reverse and making sure that the thermostat spring coil is inside the seat.
  1. Put the new gasket on the housing, put the thermostat housing back to its original position and again put the screws and also the hose, finally close the radiator drain cock and fill the coolant.

Advice

When you go to change the thermostat on a Nissan Rogue you should remove the air filter for easier access to the thermostat housing.

Caveat

Never disconnect any part of the car’s cooling system while the engine is hot.. The coolant inside your Rogue vehicle is going to be under pressure and can seriously injure or burn you if it is released from the system.

Items you will need

The articles or tools that you are going to use to carry out this substitution are the following:

  • Tray
  • Screwdriver
  • socket wrench set
  • paint scraper
  • Coolant
How to change the thermostat on a Nissan Rogue:
Nissan Rogue S AWD

Also find out about: The Steps To Programming The Remote Key Fob On A Nissan Rogue

Leave a Comment