4 Steps To Tighten A Clutch Cable Correctly!

Hi-ya! good morning, now we will made an article about 4 Steps To Tighten A Clutch Cable Correctly!

Tighten clutch system cable of your car is relatively simple. The hardest part of the job is locating the end of the cable on the transmission itself. Sometimes these can be quite hidden and in hard to reach places. Once you manage to locate it and have a full path to the riser and cable connector, tightening the cable is a simple process that can also be done with a few common household tools.

How to tighten a clutch cable?

Steps To Crimp A Clutch Cable.
Steps To Crimp A Clutch Cable.

The steps to follow to tighten the cable of the clutch system of a car are as follows:

  1. Locate the end of the clutch cable on the transmission. The clutch cable almost always connects on the side of the transmission to a lever that disengages or engages the clutch itself. It is from this end that the cables loosen because they are tightened at this point.
  1. Now loosen the cable nut. Depending on the vehicle you’re dealing with, the clutch cable nut can be a different size, so be prepared to try a few wrenches before you get the one that fits. If you have the owner’s or shop manual for the vehicle, this information can be found there. With the wrench on the nut, turn counterclockwise slightly until you can move the cable on the lift. Try not to let the cable come all the way out of the riser, because sometimes the ends fray and are extremely difficult to put back on.
  1. Thread the end of the cable through the hole in the adjuster with pliers while keeping the wrench on the adjuster nut on the riser.. When the cable is as tight as it will go, turn the adjusting nut clockwise until it seats against the cable, then loosen everything.
  1. Test your work by engaging and disengaging the clutch with the engine running. With the cable tightened and adjusted correctly, the result should be a complete disconnection and connection of the clutch. If someone is with you, have them look at the lifter while the clutch is depressed so you can make sure the cable isn’t walking on the adjuster. If the cable stays tight and the clutch does what it should, the job is done.

Items you will need

To adjust the clutch switch cable you will only need the following:

  • Pliers Wrench set (an open end will probably be needed).

Tighten clutch system cable of your car is relatively simple. The hardest part of the job is locating the end of the cable on the transmission itself. Sometimes these can be quite hidden and in hard to reach places. Once you manage to locate it and have a full path to the riser and cable connector, tightening the cable is a simple process that can also be done with a few common household tools.

How to tighten a clutch cable?

Steps To Crimp A Clutch Cable.
Steps To Crimp A Clutch Cable.

The steps to follow to tighten the cable of the clutch system of a car are as follows:

  1. Locate the end of the clutch cable on the transmission. The clutch cable almost always connects on the side of the transmission to a lever that disengages or engages the clutch itself. It is from this end that the cables loosen because they are tightened at this point.
  1. Now loosen the cable nut. Depending on the vehicle you’re dealing with, the clutch cable nut can be a different size, so be prepared to try a few wrenches before you get the one that fits. If you have the owner’s or shop manual for the vehicle, this information can be found there. With the wrench on the nut, turn counterclockwise slightly until you can move the cable on the lift. Try not to let the cable come all the way out of the riser, because sometimes the ends fray and are extremely difficult to put back on.
  1. Thread the end of the cable through the hole in the adjuster with pliers while keeping the wrench on the adjuster nut on the riser.. When the cable is as tight as it will go, turn the adjusting nut clockwise until it seats against the cable, then loosen everything.
  1. Test your work by engaging and disengaging the clutch with the engine running. With the cable tightened and adjusted correctly, the result should be a complete disconnection and connection of the clutch. If someone is with you, have them look at the lifter while the clutch is depressed so you can make sure the cable isn’t walking on the adjuster. If the cable stays tight and the clutch does what it should, the job is done.

Items you will need

To adjust the clutch switch cable you will only need the following:

  • Pliers Wrench set (an open end will probably be needed).

Leave a Comment