4 Steps To Start A Car Without The Starter Solenoid!

Hi! good morning, at this moment we will write an article about 4 Steps To Start A Car Without The Starter Solenoid!

The starter solenoid in your vehicle is the switch that supplies power from the battery to the starter motor, which cranks the engine and starts your vehicle. When the solenoid goes off, you can’t start your car and it usually gets stuck. That’s why you should keep reading and learn how to start a car without the starter solenoid.

Solenoids aren’t hard to install, but if your car won’t start, and you need a way to urgently start the vehicle one time take it to the auto parts store or mechanic. This is a dangerous procedure and will cause a short, but if you have to, it can be done.

How to start a car without the starter solenoid

The steps you must follow to get a vehicle to start without the starter solenoid are as follows:

  1. Open the lid and locate the starter solenoid. It is typically near the vehicle’s fender, near the battery.
  1. Take out the screwdriver and touch the metal end of the post that leads to the starter, opposite the one that leads to the battery. You are going to turn the screwdriver into a manual switch, bypassing the solenoid in the process.
  1. Drop the other end of the screwdriver down, touching the metal of the solenoid shaft with both terminals of the solenoid. At the same time, have an assistant turn the ignition to start the vehicle. This will cause a lot of sparks and could pass electrical current through your body if you’re not using a rubber-handled screwdriver, so you must be careful not to touch the connections for a long time.
  1. Quickly remove the screwdriver from the solenoid. If left on too long it can arc weld to both terminals, which is a bad thing. At this point, the vehicle should be running. If not, repeat the process.

Caveat

By jumping your starter solenoid, you are turning the screwdriver or other metal implement into a manual switch. If you are not careful, you can turn your body into a conductor too. Also, if you don’t remove the screwdriver from the contacts soon enough, you can burn out the starter. This is a dangerous procedure, so don’t do it unless you need to start the vehicle urgently.

Items you will need

In order to start a vehicle without the starter solenoid you must have some basic tools:

  • Rubber-handled screwdriver or other long steel tool with a rubber handle
  • An assistant to help you

You can also read: How to Fix a Starting Motor

The starter solenoid in your vehicle is the switch that supplies power from the battery to the starter motor, which cranks the engine and starts your vehicle. When the solenoid goes off, you can’t start your car and it usually gets stuck. That’s why you should keep reading and learn how to start a car without the starter solenoid.

Solenoids aren’t hard to install, but if your car won’t start, and you need a way to urgently start the vehicle one time take it to the auto parts store or mechanic. This is a dangerous procedure and will cause a short, but if you have to, it can be done.

How to start a car without the starter solenoid

The steps you must follow to get a vehicle to start without the starter solenoid are as follows:

  1. Open the lid and locate the starter solenoid. It is typically near the vehicle’s fender, near the battery.
  1. Take out the screwdriver and touch the metal end of the post that leads to the starter, opposite the one that leads to the battery. You are going to turn the screwdriver into a manual switch, bypassing the solenoid in the process.
  1. Drop the other end of the screwdriver down, touching the metal of the solenoid shaft with both terminals of the solenoid. At the same time, have an assistant turn the ignition to start the vehicle. This will cause a lot of sparks and could pass electrical current through your body if you’re not using a rubber-handled screwdriver, so you must be careful not to touch the connections for a long time.
  1. Quickly remove the screwdriver from the solenoid. If left on too long it can arc weld to both terminals, which is a bad thing. At this point, the vehicle should be running. If not, repeat the process.

Caveat

By jumping your starter solenoid, you are turning the screwdriver or other metal implement into a manual switch. If you are not careful, you can turn your body into a conductor too. Also, if you don’t remove the screwdriver from the contacts soon enough, you can burn out the starter. This is a dangerous procedure, so don’t do it unless you need to start the vehicle urgently.

Items you will need

In order to start a vehicle without the starter solenoid you must have some basic tools:

  • Rubber-handled screwdriver or other long steel tool with a rubber handle
  • An assistant to help you

You can also read: How to Fix a Starting Motor

Leave a Comment